Yes all PHASE3 gear is compatible with CH electronics.
The CH post should work, I know people were using them with O’Connell stands as well.
The included stand is of the simpler bent aluminum style stands.
-
SCAM WARNING! See how this scam works in Classifieds.
Phase3 Vaporizers
- Thread starter invertedisdead
- Start date
Yes all PHASE3 gear is compatible with CH electronics.
The CH post should work, I know people were using them with O’Connell stands as well.
The included stand is of the simpler bent aluminum style stands.
Alligator427
Well-Known Member
Thanks for your reply. I will maybe take one if pre-order still available at the end of this month.
Chicken No Name
Dazed and confused
Bodged together a stand for the zx from a CH stand and a reducer or chopped downstem.
In my case I cut the downstem so I had just the top. As this was a slightly loose fit I wrapped with PTFE/teflon tape to create a snug fit. Note: I have 3 Ch stands and all had a different id so be aware when fitting the glass.
Seems to work fine.
My only concerns are:
Thermal expansion of 3 different materials. I don't want the zx head to crack. So far no sticking of zx to glass. Slides out easy.
PTFE tape over heating. Safe op temp is advertised as 500f, which is what I have my pid at. But that is the coil temp, and not how hot the head gets. Using my infrared thermometer the hottest part of the glass interface is 200f and the Ch stand doesn't get hotter than 100f so I think the PTFE tape is fine.
Been using a few days now and no issues so far with sticking head or smells from PTFE tape.
In my case I cut the downstem so I had just the top. As this was a slightly loose fit I wrapped with PTFE/teflon tape to create a snug fit. Note: I have 3 Ch stands and all had a different id so be aware when fitting the glass.
Seems to work fine.
My only concerns are:
Thermal expansion of 3 different materials. I don't want the zx head to crack. So far no sticking of zx to glass. Slides out easy.
PTFE tape over heating. Safe op temp is advertised as 500f, which is what I have my pid at. But that is the coil temp, and not how hot the head gets. Using my infrared thermometer the hottest part of the glass interface is 200f and the Ch stand doesn't get hotter than 100f so I think the PTFE tape is fine.
Been using a few days now and no issues so far with sticking head or smells from PTFE tape.
Fearless Disaster
Well-Known Member
this fits the ch hangar stand. its a little tight but nothing that bothers me:
SKO Post
made with Grade 2 Titanium This stand is designed to shed as much heat as possible to avoid the heat getting down to the base and heating or damaging it. Suitable for use with the CH aluminum bases. Fits the SKO nicely, as well as possibly other 14mm injector heads. Post dimensions: 16 x 16 x 48mm
i love this idea! i have some reducers on the way, maybe i will try this! minus the ptfe tape maybe some high temp silicone might work depending on the temp ratingBodged together a stand for the zx from a CH stand and a reducer or chopped downstem.
In my case I cut the downstem so I had just the top. As this was a slightly loose fit I wrapped with PTFE/teflon tape to create a snug fit. Note: I have 3 Ch stands and all had a different id so be aware when fitting the glass.
Seems to work fine.
My only concerns are:
Thermal expansion of 3 different materials. I don't want the zx head to crack. So far no sticking of zx to glass. Slides out easy.
PTFE tape over heating. Safe op temp is advertised as 500f, which is what I have my pid at. But that is the coil temp, and not how hot the head gets. Using my infrared thermometer the hottest part of the glass interface is 200f and the Ch stand doesn't get hotter than 100f so I think the PTFE tape is fine.
Been using a few days now and no issues so far with sticking head or smells from PTFE tape.
Alligator427
Well-Known Member
I have the one from CH for the flowerpot that have a 2.9cm ID and the "new" one for the injector with more or less 1.8cm ID