TedJones
Well-Known Member
FC-199 maybe? It’s been awhile since I’ve had the ZX on it, perhaps a bit big, but think it’d suit what you’re looking for.
Phase3 Vaporizers
- Thread starter invertedisdead
- Start date
Spy Car
Active Member
I was just looking at those and a somewhat similar (smaller) FC-UFO (PG5034) that's also from SamL.
These seem (to me) nice they be good pairings, but what do I know? LOL
Bill
ETA: I do wish these SamL (and other brand) bongs were better about providing the dimensions of their glass pieces. *Sigh*
Last edited:
namasteIII
Well-Known Member
The ZX and finding good quality weed with healthy CBD and other non THC cannabinoid precentages has absolutely reinvigorated my love for weed.
I deliberated for a while and purchases the ZX after a 6 month break and it was a moderate risk as at that point I wasn’t sure if I was done with weed.
Everytime I use (or look at) the ZX I am filled with a joyful feeling. Thanks extensively Ryan this is easily the best vaporizer for me and I am very happy it exists.
Wish everyone the best and to any fence sitters, if you’ve got a feeling this could be the one for you, take the leap.
I deliberated for a while and purchases the ZX after a 6 month break and it was a moderate risk as at that point I wasn’t sure if I was done with weed.
Everytime I use (or look at) the ZX I am filled with a joyful feeling. Thanks extensively Ryan this is easily the best vaporizer for me and I am very happy it exists.
Wish everyone the best and to any fence sitters, if you’ve got a feeling this could be the one for you, take the leap.
Rodney
Well-Known Member
I am looking at the (ZX [14MM] Plug-&-Play Bundle) and have a few questions.
How long do we have to put in an order?
Will this ship ok to the UK and how much?
There is an option to "ADD EXTRA ZIRCONIA BOWL" is this the same bowl you get with it? so as a spare?
I really enjoy reading this thread and read a lot on reddit that this is one of the preferred coil vapes so.
How long do we have to put in an order?
Will this ship ok to the UK and how much?
There is an option to "ADD EXTRA ZIRCONIA BOWL" is this the same bowl you get with it? so as a spare?
I really enjoy reading this thread and read a lot on reddit that this is one of the preferred coil vapes so.
Spy Car
Active Member
I always put the PID over the stand for support.
Agree!I’ll load enough for a couple pulls at 35-40 degrees lower on the reading. Abv comes out very light, but well spent.
Very nice 
They will all be completed and shipping at the same time.
Probably still around 30 days out as it’s going to take some additional time to process everything as it’s been almost 6 months since I’ve been home.
My mom has finished her second round of pancreatic cancer treatment so I’m trying to get back to work and get ready to come back at it hard for the rest of this year and into the next year. Thanks a ton for your patience and support, it means and helps a lot.
I have some designs like that based on more direct laminar heating like the old Flowerpots but with improved airflow characteristics.
Recently I’ve been playing around again with my take on an Herborizer / log vape inspired design.
Love these incredible testimonials coming in, thanks so much for giving me a chance!
I’m stoked that people are finding joy and value in my work, it’s a great feeling.
You can place an order anytime but preorders are how I determine my order quantity, so to guarantee and reserve a ZX it’s recommended to place a preorder.
I try to supply what my demand requires and not a lot more. It creates some downtime, but I can’t afford to stock a bunch of stuff unless the interest is there.
Shipping is a worldwide flat rate of $20
Yes that option on my store is to add a spare zirconia bowl, some people enjoy having an extra for sharing with friends and multiple water pipes, or cycling out a fresh one during cleanings.
That’s awesome to hear people are saying some good stuff about my gear on Reddit, I need to get back on the social media wagon and try to increase my presence in the scene.
Cheers everyone and Happy Saturday Z Team
jbm
Well-Known Member
No problem, the new bowl is just gravy. Sorry about your mom, hope she is being helped.
CreatureGlass
Member
Omron just make PID's (the digital temperature controller) They're are now several cheaper makes with Bluetooth technology as Omron are top of the line and very expensive PID units(not sure they're still going or may of changed their name). To make an enail heater you'd need a PID, a solid state relay if you want to be super cautious a circuit breaker or a fuse rated at the correct amperage for not blowing prematurely(As wall plugs have fuses already the circuit breaker or internal fuses aren't really necessary but always better to have a back up I suppose) You'll also need a 5 pin Female XLR socket and a 3 pin kettle plug or PC tyoe socket and switch, obviously you can get kettle type sockets with the switch built in just get one at the correct current rating.(obviously youll need a kettle leed to plig it into the wall aswell).For an enail PID you shouldn't really need more than 3 Amp in any country maybe one could get away with 1 Amp in 230VAC countries although 3 Amp is probably better. Make sure when wiring up to ground it, I just used the grounding pin on the plug as most countries now use 3 pin pliugs thats probably the best option. Alternatively you could just screw on a wire grounding cable to the enclosure and attach the other end to something like they used to use with many electronic devices. It obviously needs wiring up and installing into some kind of housing. I used an aluminium project enclosure, which a Chinese company then promptly started using the same type of enclosure after they asked to see my diy unit(they made quartz, so didn't think there would be any harm showing them. 2 weeks later there it was up for sale by the 100s. I wish they'd done it before I built one as after buying all the parts theirs were slightly cheaper lol. There's some very cheap Crossing PIDs on sale on that Chinese Market place. That even use the same Pin out as needed (XLR enail standard)They have no physical switches though and are turned on by holding the middle button down for a few seconds so wouldn't be any good for a smart plug.The Auber has config menu. One of the parameters is for auto-shutoff.
Here is the link to the manual: https://www.auberins.com/images/Manual/RDK-300B_supplementary.pdf
Page 3 has the details
One other PID option that requires some DIY work is from Omron. They make a bluetooth enabled electronic control unit. However, I believe the rest of the hardware to connect it to the coil would need to be assembled as Omron only supplies the electronic piece. I know some folks that have used that and then have bluetooth control over their PID. I'm not a DIY expert. I believe those are expensive control units and they don't include a housing. Details on Omron can be found here:
Temperature Controllers - Product Category | OMRON Industrial Automation
These Controllers receive sensor signals and control heaters or other devices to maintain a preset temperature. They can also be used for humidity, pressure, and flowrate control. OMRON also provides temperature and humidity sensors.www.ia.omron.com
Just ordered the ZX a day or 2 ago. Hopefully I'll manage to get in on the ZXXL before they're all gone too. Although that will have to wait until I have the funds and have also purchased ZX bowl to go with the ZX
.It'd be great to see those designs become working products. The Herborizer Log Vape idea sounds like a great idea. I was thinking about a Herbalizer type log vape, not quite the same idea but very similar lol although different heating styles. I just double checked as thought the herbalizer disappeared long ago, it looks like they're now back in production unless it's a dodgy site looks legit though.I always put the PID over the stand for support.
They will all be completed and shipping at the same time.
Probably still around 30 days out as it’s going to take some additional time to process everything as it’s been almost 6 months since I’ve been home.
My mom has finished her second round of pancreatic cancer treatment so I’m trying to get back to work and get ready to come back at it hard for the rest of this year and into the next year. Thanks a ton for your patience and support, it means and helps a lot.
I have some designs like that based on more direct laminar heating like the old Flowerpots but with improved airflow characteristics.
Recently I’ve been playing around again with my take on an Herborizer / log vape inspired design.
Love these incredible testimonials coming in, thanks so much for giving me a chance!
I’m stoked that people are finding joy and value in my work, it’s a great feeling.
You can place an order anytime but preorders are how I determine my order quantity, so to guarantee and reserve a ZX it’s recommended to place a preorder.
I try to supply what my demand requires and not a lot more. It creates some downtime, but I can’t afford to stock a bunch of stuff unless the interest is there.
Shipping is a worldwide flat rate of $20
Yes that option on my store is to add a spare zirconia bowl, some people enjoy having an extra for sharing with friends and multiple water pipes, or cycling out a fresh one during cleanings.
That’s awesome to hear people are saying some good stuff about my gear on Reddit, I need to get back on the social media wagon and try to increase my presence in the scene.
Cheers everyone and Happy Saturday Z Team
Last edited:
That brush has seen some shitI always put the PID over the stand for support.
They will all be completed and shipping at the same time.
Probably still around 30 days out as it’s going to take some additional time to process everything as it’s been almost 6 months since I’ve been home.
My mom has finished her second round of pancreatic cancer treatment so I’m trying to get back to work and get ready to come back at it hard for the rest of this year and into the next year. Thanks a ton for your patience and support, it means and helps a lot.
I have some designs like that based on more direct laminar heating like the old Flowerpots but with improved airflow characteristics.
Recently I’ve been playing around again with my take on an Herborizer / log vape inspired design.
Love these incredible testimonials coming in, thanks so much for giving me a chance!
I’m stoked that people are finding joy and value in my work, it’s a great feeling.
You can place an order anytime but preorders are how I determine my order quantity, so to guarantee and reserve a ZX it’s recommended to place a preorder.
I try to supply what my demand requires and not a lot more. It creates some downtime, but I can’t afford to stock a bunch of stuff unless the interest is there.
Shipping is a worldwide flat rate of $20
Yes that option on my store is to add a spare zirconia bowl, some people enjoy having an extra for sharing with friends and multiple water pipes, or cycling out a fresh one during cleanings.
That’s awesome to hear people are saying some good stuff about my gear on Reddit, I need to get back on the social media wagon and try to increase my presence in the scene.
Cheers everyone and Happy Saturday Z Team
Funny thing is I think it possibly works better with these stiff war-torn bristles
I try to brush after every bowl, with the bowl upside down! (Ideally we want to brush debris OUT, not sieve it THROUGH the screen)
