JoDa Glassworks

z9

Well-Known Member
I believe that the cores on the UD and HI are 3/8" and the Nano is 10mm. Don't quote me on that, just going off of memory. These stems might fit, I know it was reported that some of the thick stems Andy made did fit other logs and possibly the Solo.

If they do fit I would love to get a couple worked glass stems for my UD and HI which I should be receiving soon. If money wasn't so tight right now so I would have already purchased a couple and been the guinea pig.

The amber purple is without a doubt my favorite color combo I've seen yet.
 

Tweak

T\/\/34|<
I believe that the cores on the UD and HI are 3/8" and the Nano is 10mm.

This is what I remember.

On Toasty-top.com it states:

"The HI can be used with two different roasting tube styles. It will accept 5/16" diameter stainless steel roasting tubes inside the center tube as with traditional direct draw convective vaporizers. It will also accept 3/8" inside diameter high temperature medical grade silicone roasting tubes on the outside of the center tube. 10mm glass or wood roasting tubes can also be used. "

some of the thick stems Andy made did fit other logs and possibly the Solo.

8f7SENyl.jpg

Mine did. Fits almost too snug. Flavour is great.
 

VaPeD&CoNfUsEd

JoDa Glassworks
Glass Blower
Ladies and gents.......... MEGA MAI TAI!!!!!

vmFkLO6.jpg

And the pics still don't do this amazing color any justice at all!

On a side note:
To any and all of you waiting on your orders, they will be shipped tomorrow. Sorry for any wait. Fedex took their precious fucking time delivering my last batch of gongs.

EDIT: the above stem is for sale. 27$ shipped.
 

Caligula

Maximus
Ladies and gents.......... MEGA MAI TAI!!!!!

vmFkLO6.jpg

And the pics still don't do this amazing color any justice at all!

On a side note:
To any and all of you waiting on your orders, they will be shipped tomorrow. Sorry for any wait. Fedex took their precious fucking time delivering my last batch of gongs.

EDIT: the above stem is for sale. 27$ shipped.

So are we going to see a fully worked stem with that color anytime soon? Also whats the deal with your phone? Are you having issues taking macro shots or what?
 

VaPeD&CoNfUsEd

JoDa Glassworks
Glass Blower
Ok all outstanding orders have been shipped and your tracking numbers are in your inboxes.

I am expecting a solo and a stem within the next 2 days and will get to busting out some solo stuff. So think hard about what you want and get your Paypals stocked up. ;) I'm down to 1 18mm gong left again so I'll be making an order for those as well.
 

VaPeD&CoNfUsEd

JoDa Glassworks
Glass Blower
As a matter of fact.... Look what was in the mailbox when I checked it a minute ago.

LIJJYyt.jpg

BIG thanks to @stickstones for the stem and to @al bundy for the broken solo!!! Freebies for the both of you soon!

So it looks like I need to order in some 14mm tubing. Solo bowl is 15 stem is 14 except at the polished lip it's 14.5. So Andy's basket screens should still work well might just have to open them up a hair for a nice tight fit. I wish I could source those on the cheap to be able to provide them myself but Andy can't give me a bulk discount because he makes them all by hand. So for now everyone will have to provide their own screens.

Anyways in order to place an order for my solo tubing I need a few more sales on my nano stuff. So if you've been thinking about pulling the trigger on one of my pieces now is the time. So 5$ off any of my advertised prices.

Or if anybody wants to pre order solo pieces I'll give deals on those too. It'll just be a bit longer of a wait than normal. (Not much tho)

I'm confident that as soon as I have the correct tubing that they will be relatively easy for me.

Ain't nothin to it but to do it!
 

syrupy

Authorized Buyer
A second vote for a nice thick carb cap. Both the TI caps I purchased have 23mm inner diameter, and fit all of my TI nails, quartz nails with dome, and quartz banger. I believe many nails that use carb caps are 20-23mm diameter. It doesn't have to be a flush fit with the nail. My nail is 21mm so there is a little sideways play, but the seal is on the ceiling of the cap, not the sidewalls, so the diameter is not critical as long as larger than the nail. Most carb caps have a 3.5 inch shaft that doubles as a dabber. For glass I'd rather have a 4 inch shaft that is much thicker, since with a worked carb cap I'd rather not chance breaking the glass cap's dabber end by dabbing with it.

My dream is a an igloo or teepee carb cap with a little tube chimney around the carb hole.

highly-educated-carb-cap-with-ballpoint-tip-dabber-265px-390px.jpg
 

VaPeD&CoNfUsEd

JoDa Glassworks
Glass Blower
I will be doing both of the above and more. Just gotta knock a few more sales down so I can place an order for the correct tubing.

14mm heavy wall (2.2mm wall) tubing will give me the o.d. of a standard solo stem and the i.d. of a nano stem. So, not only will Andy's basket screens work perfectly, the stems will be beefy as shit!

Don't quote me on this part yet but, in theory with those dimensions these could possibly be dual purpose nano/solo stems with just an adjustment of the basket screen. Wouldn't that be handy! But I'll have to experiment with that part.
 
Last edited:

2clicker

Observer
V&C, i would like to pre order a set up like i pictured a page back. the solo gong w/ sherlock style dry mouth piece attachment.

anyway, i will try to update the photoshop image and sizes and shoot them over to you. is this enough to get a quote?
 

VaPeD&CoNfUsEd

JoDa Glassworks
Glass Blower
My only problem with that is the bent mouthpiece. To be honest I don't know if I can pull it off. You see, to bend tubing properly you need to get a large part of the piece your working on equally hot. Which would be fine and dandy if I wasn't on such a small torch. I wouldn't be comfortable accepting anybody's money on a project that I can't confidently say I can pull off. When I got into this I figured I'd be cranking out all kinds of cool bendy pieces. So far it's one of my greatest challenges that I've yet to successfully pull off.
 

2clicker

Observer
My only problem with that is the bent mouthpiece. To be honest I don't know if I can pull it off. You see, to bend tubing properly you need to get a large part of the piece your working on equally hot. Which would be fine and dandy if I wasn't on such a small torch. I wouldn't be comfortable accepting anybody's money on a project that I can't confidently say I can pull off. When I got into this I figured I'd be cranking out all kinds of cool bendy pieces. So far it's one of my greatest challenges that I've yet to successfully pull off.

ok what about two of the gong stems alone?
 
Top Bottom