Pen Imag Plus

Meach

Well-Known Member
Fixed temp version or 3 temp version anyone have both ? Which do you prefer? Only have access to fixed temp version at this time..local shop has a few in stock...he's selling em on the cheap and want to know if ill really be missing anything by going for the fixed temp version?
 
Meach,

Shit Snacks

Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
Yes @paytonpenn I was told the same thing. Sounds like they're almost ready.

@snamuh did you run burn offs? Initial offgassing and smell goes away after several empty sessions on red, plus a quick ISO swab

@Meach check out the regular Imag thread too, the replaceable battery is a pretty big deal I think if you can get some spares, but the way the original works is it rises temp from low to high in the 2-3min session, other than those two differences it should be the same (until the new Imag Plus is out)
 

snamuh

ghost
It is pre owned but pretty much new. I ran two red burn off sessions..

I didn't expect it to be the best for taste or anything.. Kinda just an experimental buy... It will suite my need for occasional portability though
 
How nice would Ed's stem look on this?

Imag_13__36354.1411715347.1280.1280.png
 
Is it possible the ones on the W9 ARE the new ones? They are listed at $99, which is higher than others have mentioned here.
 
TheDudeNextDoor,

TNT_error

Well-Known Member
The ones on w9 are still the Imag+ @TheDudeNextDoor . From what I've read, the imag2 doesn't have a release date yet. It's wider and shorter than the imag+. Check out imagvape.com. They show the imag2 on there.
 
TNT_error,
  • Like
Reactions: NorVape

Shit Snacks

Milaana. Lana. LANA. LANAAAA! (TM2/TP80/BAK/FW9)
The ones on w9 are still the Imag+ @TheDudeNextDoor . From what I've read, the imag2 doesn't have a release date yet. It's wider and shorter than the imag+. Check out imagvape.com. They show the imag2 on there.

This new Imag Plus update is separate from the Imag2 and Imag Pen they are working on. They're are not released just yet, so w9 doesn't have them either. Just the original Imag Plus.

@TheDudeNextDoor they were lower bc it was easier to get them on alibaba before. Also w9 had a coupon code
 

elproducto

Member
My Imag+ has stopped working for some reason. I used it twice this morning and put it on the charger. When I went to go use it again it is not responding to button presses. I pressed the button 5 times to make sure it was not locked. I put the Imag back on the charger, charging indicator goes from red to green instantly, so battery is charged. I clicked the button again after putting the device on the charger and the button blinks blue for like a second, so button is making contact with the mechanics of the Imag+. I take it off the charger again and it is not respond to button presses. Seem like it is stuck in lock mode. Gotta go reach out the seller again.
 
elproducto,

Kaptan

Well-Known Member
My Imag+ has stopped working for some reason. I used it twice this morning and put it on the charger. When I went to go use it again it is not responding to button presses. I pressed the button 5 times to make sure it was not locked. I put the Imag back on the charger, charging indicator goes from red to green instantly, so battery is charged. I clicked the button again after putting the device on the charger and the button blinks blue for like a second, so button is making contact with the mechanics of the Imag+. I take it off the charger again and it is not respond to button presses. Seem like it is stuck in lock mode. Gotta go reach out the seller again.
I had the exact same problem with mine. It started happening after only 9 days of use. I was promised a replacement when the new changes are completed.
 
Kaptan,

elproducto

Member
Why 5 instead of 3?
Guess you where right about clicking the button three times. My seller stated he contact the manufacture and there recommendation is to charge the IM+ fully until the green indicator is shown. Once you have the green indicator leave IM+ on the the charger and click the button three time to engage and reset the unit. I Did the steps recommended, it did not resolve my issue however. I posted a video below showing the issue. This was my first attempt of moving to vaping from combustion, any recommendation on what I should purchase next?

https://vid.me/MLgl
 
elproducto,

Kaptan

Well-Known Member
Guess you where right about clicking the button three times. My seller stated he contact the manufacture and there recommendation is to charge the IM+ fully until the green indicator is shown. Once you have the green indicator leave IM+ on the the charger and click the button three time to engage and reset the unit. I Did the steps recommended, it did not resolve my issue however. I posted a video below showing the issue. This was my first attempt of moving to vaping from combustion, any recommendation on what I should purchase next?

https://vid.me/MLgl
Mine does the exact same thing. Get a refund.
 
Kaptan,

snamuh

ghost
My mp was getting clogged so I found a plain glass chillum/glass tube and it fits right into the bowl... It works amazing I just pack it and then stick the chillum in. I don't even use a screen. I can also pack the bowl like 1/2 way maybe less and it seems like it hits better than the original mp with a full pack..

Its pretty ugly though. Lol maybe I can widdle a wood piece to hold the glass.

Also I have been using this as my driver which I said I wouldn't. Its just so much easier than my VG and mflb. I haven't really noticed the weird taste and smell that I mentioned when I first got it... Probably because its getting pretty dirty
 

PPN

Volute of Vapor
My unit is still working, the mp is broke like for others but I think it's not working so hot like before even if I use it only 2 or 3 times per day (somedays I don't use it at all) and I get the sensation that more I use it lore it taste bad...but I never cleaned it...maybe it's time to do it!

I think this unit will not resist to a heavy duty use a longtime!
 
PPN,
  • Like
Reactions: CHIDOY
Top Bottom