Healthy Rips Rogue
- Thread starter oddjobold
- Start date
Jill NYC
Portable Hoarder
They have excellent customer service, so I am sure they will take care of you.
However, before you go through all that, have you given your oven a good cleaning?
Here is a post on how I clean it, just in case it helps.
https://fuckcombustion.com/threads/healthy-rips-fury-edge.42141/post-1570863
Petetbay
Well-Known Member
When it’s still warm, turn it upside down and wipe the bowl bottom with ISO soaked q-tips then blow in the air inlet with the device on. They might replace if still under warranty, but they might ask you to do what I said before replacing.
Astedra
Well-Known Member
Yeah mine has just stains to. But the holes don't seem to have anything in them but something is blocking the air flow, and it's not the cooling unit. I wrote to costumer service.
Last edited:
Complacency media
Active Member
I would double check the holes with a light and a needle. I had a friend that bought a brand new unit and I didn’t think to mention until after, that I definitely have to regularly clean the char or buildup in the holes with a needle and a light. it builds up faster even at higher temps or if you’re using dabs. This is a frustrating issue with 99% of vapes, if healthy rips makes it easier to clean the bowl screen and air path it’d be a nearly perfect portable, final thing would be all glass for me 
.
.
Last edited:
GetLeft
Well-Known Member
Excuse my interruption. I don't have a Rogue, but I use an Edge daily. I pay minimal attention to the bowl but pay close attention to the screen and the stem I use (a bubbler stem). When things bog down, that's where the problem is not the bowl. Not to say I shouldn't be paying a little closer attention to my bowl. But since no one mentioned cleaning the screen I figured I'd throw it out there.
Hi All!
@Astedra, thank you for contacting our CS team! Please follow the instructions that our CS gave you - this should resolve your issue. If not, we'll take care of you - no worries!
Thank you all for the excellent and helpful suggestions regarding an airflow restriction! We will add a few suggestions as well:
1. Turn your device on max temp (430F) and gently blow through the intake holes at the bottom of the device. This should dislodge and/or burn off any fine debris that may have found its way through the tiny chamber holes over time.
2. Take a small pin or needle and carefully poke through the bottom intake holes - BUT NO MORE THAN 1/4 INCH or you could potentially damage the device. Then gently blow through the mouthpiece at max temp (430F) to clear any debris.
3. MOST IMPORTANT TIP: Always use a coarse or medium grind and you will never have a clogging issue! Don't over-grind your material to a fine grind - you only need to turn your grinder once or twice - that's it!
What an awesome community - always polite and never abusive - so impressive compared to other social media!
Watch for something classy soon - you are the first to hear
We are always here for you,
-Healthy Rips Team
@Astedra, thank you for contacting our CS team! Please follow the instructions that our CS gave you - this should resolve your issue. If not, we'll take care of you - no worries!
Thank you all for the excellent and helpful suggestions regarding an airflow restriction! We will add a few suggestions as well:
1. Turn your device on max temp (430F) and gently blow through the intake holes at the bottom of the device. This should dislodge and/or burn off any fine debris that may have found its way through the tiny chamber holes over time.
2. Take a small pin or needle and carefully poke through the bottom intake holes - BUT NO MORE THAN 1/4 INCH or you could potentially damage the device. Then gently blow through the mouthpiece at max temp (430F) to clear any debris.
3. MOST IMPORTANT TIP: Always use a coarse or medium grind and you will never have a clogging issue! Don't over-grind your material to a fine grind - you only need to turn your grinder once or twice - that's it!
What an awesome community - always polite and never abusive - so impressive compared to other social media!
Watch for something classy soon - you are the first to hear
We are always here for you,
-Healthy Rips Team
Come here to fix my milkshake draw, and fixed it within a page!!! I had done the upside down heater on iso and the needle in the holes, for me it was the blowing through the air path out the heater.
Great device, wish my MP would still clip and I wouldn’t have to rubber band it, but I got a new MP on the way so fingers crossed it’s not the device.
Was favouring the arizer for a little while, but this thing is hitting after a nice gentle blow
Edit to add, I am obviously going to use a courser grind as advised above *
Great device, wish my MP would still clip and I wouldn’t have to rubber band it, but I got a new MP on the way so fingers crossed it’s not the device.
Was favouring the arizer for a little while, but this thing is hitting after a nice gentle blow
Edit to add, I am obviously going to use a courser grind as advised above *
Complacency media
Active Member
Yeah would be great if healthy rips constructs the device in a way where we can fully clean the chamber, or at least the screen and the full air path. I now have a glob on the bottom holes of the vape. great device tho I really love it, it’s been fantastic for dabs but I’m definitely getting cement straw draw rn and am going to have to void my warranty at least the lifetime to open the device and clear the blockage.
vapviking
Old & In the Way
Anyone else doing rosin in their Rogue?
Asking for a friend whose only device is a Rogue and recently came into his first rosin.
I don't think Rogue comes with a concentates pad...
My inclination is to suggest embedding rosin in cotton or hemp fiber, or I suppose in some flower. They have no wpa or water tool, so it would be upright use, standard stem.
Actually, and as @Complacency media has learned, this is probably eventually going to have some downsides, but I'd like to be able to get my friend to have something of a rosin experience.
Asking for a friend whose only device is a Rogue and recently came into his first rosin.
I don't think Rogue comes with a concentates pad...
My inclination is to suggest embedding rosin in cotton or hemp fiber, or I suppose in some flower. They have no wpa or water tool, so it would be upright use, standard stem.
Actually, and as @Complacency media has learned, this is probably eventually going to have some downsides, but I'd like to be able to get my friend to have something of a rosin experience.
Complacency media
Active Member
I literally just put a small amount of flower like enough to use as a base against the bowl screen to keep the dab close to the heat source, it actually works pretty well. I use it at 420f and put quartz pearls into the stock mouthpiece for a travel friendly cooling alternative (credit to table top bong for the tip). as stated above a small dab will help keep things clean and when dealing with the higher end temps the screen gets clogged immediately, like I was cleaning the screen with the unit on and char was building up as I was blowing through the air path. but I tend to put a pretty big glob on there and get like four huge rips. I did just get an xmax qomo because it seems like the most pocketable erig, and im definitely wasting wax since i have to dump the herb after a few hits because of the burnt taste.
Hey All! Our 4th of July sale is on now! Save 15% storewide with Coupon Code: FREEDOM15
Storewide sale includes:
FURY EDGE SE: $101.15
ROGUE SE: $118.15
Happy 4th!
-Healthy Rips Team
Storewide sale includes:
FURY EDGE SE: $101.15
ROGUE SE: $118.15
Happy 4th!
-Healthy Rips Team
Healthy Rips Dry Herb Vaporizers. The best portable Dry Herb Vaporizers
Best Dry Herb Vaporizers. Healthy Rips ROGUE, FURY EDGE Portable High End Dry Herb Vaporizers That Everyone Can Afford.
www.healthyrips.com
Chronicele
Well-Known Member
I just want to give some love to the updated HR Rogue. I also have the TM2 and TB2 and not a session guy, but still find myself picking up the rogue and being impressed with the extraction efficiency and ease of use & cleaning. Cheers!
hirmando
New Member
Another happy Rogue SE user here. I use the dosing caps exclusively for and get good results from an aftermarket sidecar bub like the one below. I also have a WPA for use with a full glass rig.
The device fit and finish is great (if you like satin fishes), heats up quick and allows for both flavor and think clouds depending on your temp and pull. Cleaning is simple for the dosing caps and I have not needed to clean the oven at all since purchase in jan2024.
Would have preferred a removable battery and an all glass vapor path but am otherwise very satisfied.