kokolokokolokon
Well-Known Member
Does anyone tried this for bigger devices?
Not at max power of course
Not at max power of course
DIY Induction Heater Builds and References
- Thread starter TommyDee
- Start date
TommyDee
Vaporitor
I think this requires a center-tapped coil @kokolokokolokon since it only has one choke.
132ikl
Member
Thanks for the pointers.
actually looking at 11.67V, which definitely still good.) I've got an M'21. I can live with a weak cap, I just wanted to make sure I wasn't doing something wrong Also came across this old Reddit comment of yours about cap gain ratios after doing some searching, very helpful. Have you done any more measurements since then? Might upgrade to a new cap if in the future I decide I'm not satisfied
Last edited:
TommyDee
Vaporitor
My last measurements were of some 419 caps I got a few years ago with the 3rd batch of cap materials. They came in at a GR of 5:1. The '3rd batch' was of the original source. Learned since then that making 304 stainless steel magnetic requires work hardening the material. That means is it all about the tooling.
tokenknifeguy
Well-Known Member
Has anyone made one of these induction heaters for the Dani Fusion? I know most are geared toward the vapcap. I really would love to build my own induction heater, but I have no real knowledge of electrical mumbo jumbology. I just want one that I can plug into the wall and able to heat up my Fusion within like 10-20 seconds. I've seen folks using an ih for the dani and it taking closer to a min. Is there a good website that lists items needed and how to put it together?
kokolokokolokon
Well-Known Member
to reach that times you would need a stronger pcb than the usual one. For example:
Also I would recommend a dial regulator for the power (in the previous link, it can reach 1000W in theory….you dont want to use it at 1000W and it is good to find a sweet point with a dial).
Even you can get a screen to see the power, or a timer.
This are just examples and im not a pro making IH’s. I hope someone more can give you some tips!
TommyDee
Vaporitor
Watts is watts. Eventually everything will heat up, so the question is, wat rate of heating do you want. 120 watts based on the standard module is nothing to sneeze at. I find 60-70 watts to work out perfectly for a DV. This says you can easily double the mass of the tip/cap and still have a very good heating rate. Problem with faster heating is that the bake suffers in several ways.
Edit: I've run constant current power supplies on the standard module to manage variable input power. Works great.
Edit: I've run constant current power supplies on the standard module to manage variable input power. Works great.
2tiki
Well-Known Member
When I clicked on your last link, it was a 404 not found page. I have one of these: https://www.amazon.com/gp/product/B083GG2H6R/?th=1
Would that work well for most (if not all) dynavap, dani, etc, type of devices? Should it work with the up to 12v induction heater kits? Should it heat things just as fast as the Ispire Wand?
Could I use it with the more powerful IH that you link to, as long as I don't put it past 12 v? If so, would that be safer than using the 12v IH if I want to get it to 11v-12v?
What would I need to buy to connect the IH kit to the power supply? I assume there is a name for whatever wire plugs into the power supply, and whatever plugs into the IH kit.
Do both kits you link to, come with the coil, or do I need to buy that separately?
Thanks!
I use the original induction heater from the 1. post at page 1 with a 12V 5A power supply and it work well with my Dani fusion. Heating time is around 20 seconds for first click, following clicks are around 12 second.