Maybe he does have a super wand or something lol, but yea a torch is def faster but I like the ih hits more for some reason
if it touches the coil I believe it turns off for a second idk since I don’t have the device yet I can’t answer any of these questions for sure, just going off what I read and my brief convo with the creator.
I was having similar issues as you but I switched to using a micro torch lighter and aiming between the bottom ring and the base of the cap + 1-2 seconds after the click. It's been producing big tasty clouds and finishing the bowl in one heat cycleYes , i have tried most torch sizes available,it is actually the nozzle diameter that matters. I just cannot get a sweetspot with anything and counting 8 seconds after the click when i am baked,makes me forget there is a click at all. I might have monkey memory or idk,but my clicker is no good indicator for anything . I have minimized airflow to the minimum. As mentioned i am having better results with my Dani V3 cap on the fusion tip ,so there is something wrong with mine or this vape is just not for me)... It is just that the 14 day return period is running out and if i could not master it in two weeks,i probably wont ever. The only thing usable of the package i got is the tip paired with the V3 cap,not really cashwise for me to keep it.I have tried a lot of vapes and own quite a few flamepowered Vapo-bowl,vaporstar,,Vapor-genie,Blackleaf Wand Vape ,Gn0me,celtic -vapo ,vapocane,vaponic,vapcap,vapman,dynacrap,,lotus,dani v3, ball torch vape ,in other words you can say i am a big fan of those and i really wish my Fusion could perform anything like the v3,maybe if i didnt own the V3 i would have appreciated this one more,who knows.
Also i wanna note ,that temp stepping via reheating works very well with my Dani V3 , while with the fusion it just goes from wispy vapor ,to charred and i just cannot seem to nail the sweetspot with the stock setup and get that thick tasty hit.
I'm not talking to you guys all weekend yaw jinx me I'm still trying to get the burnt taste out . As it is nice to know how to slam a bowl it's not my normal vape stile .
I wonder if your cap is defective? All I know is when I do my higher temp hits with the double torch, 1in long flames, heating the bottom half of the bottom ring until click or 1 or 2 sec after, then heating the top half of the top ring for some more seconds...I get thick but smooth ecig like vapor out of this thing.Will give my fusion last chance this weekend and after that i will probably return it,going to make some videos and send them to BFG for analysis,but at this point as much as i like the aesthetics of it,compared to my Dani v3 i cannot really find the same value especially at the bumped priced tag. Not really satisfied with the vapor density i am getting and it is pretty useless for me with a medium sized pockedtable torches i can use the V3 with. The Fusion tip with the V3 cap is definetly a better experience then the stock, i also have noticed that it does do well if you do not rotate with the new tip. Anyway i hope they iron out the difficulties as the V3 is one of my favorite vapes ,i should have just gone with a TI tip,instead all this.
Anyway on a side note, i havent tested how much it cools,as i dont want to vape through that stem ,but i noticed it fits TM stems !!!
Something just hit me we talk about witch ring we are heating . But not weather it's the silver or SS rings I'm heating the SS ring at the very bottom of the cap!
Sharing is caring
your Tip seems tighter on the stem now, all you did was take an Oring off?
Nice!
How is the threading when putting the cap on?
I can confirm the screens are not the same as I noticed mine had gotten pushed inward leaving only the small hole in the tip block even more by the screen .. so right now running it slightly off the bottom of the tip for more even airflow will probably make a ss wire ring to go under it
In a similar position, except I have the v3 SS and Ti tips, and my Castle and Fusion are due to land soon - when I hope to write up a comparison of all 4.
My fusion screen was bent inwards natively when I received it. Works fine though. The vape gets clogged faster at the spiral than the screen. My spiral was alot dirtier than pic above after one week
Do you think it would get less dirty if it had a carb hole?My fusion screen was bent inwards natively when I received it. Works fine though. The vape gets clogged faster at the spiral than the screen. My spiral was alot dirtier than pic above after one week
Based on personal use and gunk pattern from it I would imagine it's directly related to the volume of product you feed through it and how fast you gunk up will be more a reflection of that than anything else
I was thinking it could be more dirty because you cant clear the stem like you can when there is a carb.Based on personal use and gunk pattern from it I would imagine it's directly related to the volume of product you feed through it and how fast you gunk up will be more a reflection of that than anything else
A longer stem with a carb cap might have a spiral that gets dirty more slowly but only because there's more space for gunk to build up in the longer stem.
My glass stem only 1 I have not ran it on yet my hunch is its going to be my favorite .but I keep it locked away so I don't brake and only use specific times it is just a standard bfg glass stem I will try it tonight .but today I have both on me so it's play time
that was the case with my screen I'm not claiming more airflow just more even airflow and less screen cloggingMy fusion screen was bent inwards natively when I received it. Works fine though. The vape gets clogged faster at the spiral than the screen. My spiral was alot dirtier than pic above after one week