MrBaked.co
Well-Known Member
People in the UK were told to purchase from the US because that is where they will ship from.
I don’t know if they were on the site already, but for now it says they are out of stock.
AirVape Legacy Pro
- Thread starter JohnJacobs
- Start date
StringTheorista
Well-Known Member
It’s more likely IMO that they haven’t arrived on the EU site yet, and it’s just showing an “out of stock” banner as a placeholder instead of the “coming soon” banner we saw on the US site. Gary said they were held up in customs for the EU site, and anticipated 10 days if I recall correctly. I don’t think they came and went that quick, is what I’m saying
Okla68
Well-Known Member
Dave...sorry to pop your bubble about the gold oven, but, No on oven Staying SPARKLY, it Dosent, at least mine hasn't. No amount of ISO or Everclear seems to remove the Stain(Id post a pic if I knew how). The Only way ive found is to litterly Scrap it with a metal tool/implement. It seems to be tough in that it doesn't seem to scratch the surface. Been tempted to try Steel wool on it. I use mine several times daily, alternating with the Airvape X. I find it to be a Top Notch vaporizer. As far as cleaning, I do a cursory wipe down after each load and full clean about once a week. Thats using Flower and Flower/Concentrate(Home squeezed Rosin) sandwiches. 95% of time mine is used at home(retired).
Yes, the capsules will definitely help with the loading and unloading.
Would I recommend it to others, Yes most definitely.
vandalizedbythelotus
Well-Known Member
it's a bit of a pain but i got into the habit of just wiping it after every use, this seems to keep the gold bits very clean.
please don't try metal tools on it, IMO the risk of damage is too high, some heat and solvent should work.
i think capsules will improve the ALP immensely and despite my bitching i already consider it to be in the top 5 portables currently.
until then i cut a 16mm fine mesh screen and domed it slightly.
half bowls with the domed screen on top vape wonderfully and evenly, no stirring required.
you can use imgbb.com to post images here, just select the bbcode formatting from the dropdown
vandalizedbythelotus
Well-Known Member
@Gary-Airvape can we please have the "Smell Proof Bum Bag" added to the EU shop as well? thank you, happy holidays!
Dr. G
Vapman Collector*Vapman Beta Tester
YAY! I agree so much! I am just happy about the capsules...that will solve the on the go prob.
warren0728
Well-Known Member
I was cleaning my legacy pro and used one of the small q-tips included with the vape. while I was cleaning the hole where the glass pathway connects to the end of the vape with the oven (not the end that leads to the mouthpiece) ... I stuck the q-tip into the hole and when I pulled the q-tip out the cotton came off and is lodged inside the hole blocking which of course blocks the air path/flow to where I can barely draw air through it. I have tried unsuccessfully to pull the cotton out of the hole but I can't get it to come out. is there a way to remove the silicon grommet to get at the inside better or do you have any suggestions on removing the cotton ... its basically unusable as it is now. hopefully this makes sense
I contacted airvape support through the website but figured the knowledge base here might have suggestions.
here's a pic of the hole/area I am talking about.
I contacted airvape support through the website but figured the knowledge base here might have suggestions.
here's a pic of the hole/area I am talking about.
seedy53
Well-Known Member
remove oven screen and blow through side of oven screen hole.
goto a oil change place or mechanic shop, ask someone to use air tool to blow-it out .
blow compressed air in to the small oven's side-screen.
come out the rubber grommet for glass tube, q-tip stuff should fly out of there.
goto a oil change place or mechanic shop, ask someone to use air tool to blow-it out .
blow compressed air in to the small oven's side-screen.
come out the rubber grommet for glass tube, q-tip stuff should fly out of there.
Last edited:
Hi,I was cleaning my legacy pro and used one of the small q-tips included with the vape. while I was cleaning the hole where the glass pathway connects to the end of the vape with the oven (not the end that leads to the mouthpiece) ... I stuck the q-tip into the hole and when I pulled the q-tip out the cotton came off and is lodged inside the hole blocking which of course blocks the air path/flow to where I can barely draw air through it. I have tried unsuccessfully to pull the cotton out of the hole but I can't get it to come out. is there a way to remove the silicon grommet to get at the inside better or do you have any suggestions on removing the cotton ... its basically unusable as it is now. hopefully this makes sense
I contacted airvape support through the website but figured the knowledge base here might have suggestions.
here's a pic of the hole/area I am talking about.
Did you try to open the top side? where the little gold screen is? you can have better access from there. Also, the best tool is an interdental brush
warren0728
Well-Known Member
i have a small compressor … i’ll give that a try
are you talking about the screen at the bottom of the oven? i don’t know that was removable
i did remove that screen but wasn’t able to do get to it from thereHi,
Did you try to open the top side? where the little gold screen is? you can have better access from there. Also, the best tool is an interdental brush
also … it seems that when i try to get to it from the grommet all i do is push it further in … i tried a small pick tool with the end bent up a little hoping i could snag it and pull it out but no success … it is probably covered with resin which makes it harder to get out
JustAnotherCritic
Well-Known Member
I use a hemostat for sewing and they fit into that hole, I've used it to retrieve lost qtips in that spot before. Fine enough needle nose pliers would work too. Maybe look into getting a pair, they're useful for a ton of stuff. Wish I had a better idea in the meantime, but sounds like it's pretty stuck. You can get hemostat at stores with sewing equipment and pliers at hardware stores/fishing stores so if you live near one it might be worth a trip.
Pepeluis33
Well-Known Member
No, AFAIK that's not removable, I'm pretty sure @seedy53 meant the oval top side screen
Good idea! I'm wondering that maybe this can be used for a deeper clean as well? plug one end of the airpath (maybe by adding a plug inside the glass?), leave the glass tube installed, place ALP vertically, fill-in the airpath with iso and leave it for a while (not too much because of the different non-iso resistant materials like silicones and peek, just enough to dissolve the build-ups)
To me the most important drawback of this device is the difficulty in cleaning the airpath.
Last edited:
vandalizedbythelotus
Well-Known Member
while the part near the oven seems to be a single block of peek with a silicone grommet, the L shaped one near the mouthpiece appears to be less airtight. i'd be wary of it leaking liquid inside the unit.
StringTheorista
Well-Known Member
@Gary-Airvape you might want to consider making your website a bit more user friendly. E.g., you can’t find the “air bubbles” unless you know that’s what they are called; if you search “dosing capsules”, no product shows up, and the only things that show up under the “shop” tab are vaporizers, not accessories. Why not have drop down menu links for accessories? There’s no readily findable site map, either
Searching “accessories” does not take you to the “accessories and parts” page, it goes to a page that intersperses accessories with blog posts. To get to a page showing all accessories and parts, you have to follow a link from the Airvape X FAQs page.
Searching “accessories” does not take you to the “accessories and parts” page, it goes to a page that intersperses accessories with blog posts. To get to a page showing all accessories and parts, you have to follow a link from the Airvape X FAQs page.
SpreesTrip6
New Member
There is definitely a drop down menu with a site map. Make sure you're not double tapping when you click shop and it should take you to a sub menu inside the drop down. That's where you'll find the accessories link.
Deano
Well-Known Member
I tried searching before I posted but couldn't find anything on modified S&B capsules.
Has anyone tried to cut and reduce the height of another capsule to fit the Legacy Pro?
I know they just officially released but they're already out of stock just as I was preparing to place an order. I have a few Crafty capsules I thought about trimming with a Dremel to test out.
Has anyone tried to cut and reduce the height of another capsule to fit the Legacy Pro?
I know they just officially released but they're already out of stock just as I was preparing to place an order. I have a few Crafty capsules I thought about trimming with a Dremel to test out.
StringTheorista
Well-Known Member
Maybe not on IOS? I’ m using my iPad and not finding a drop down…
This is what I see on the home page
And this is what shows up when I follow the “shop” link, single tap:
Puddentain
Well-Known Member
I’m on an iPad as well. Click on “shop” again and it will expand to the whole product line and accessories. At least it does for me.