Stone__Man
Well-Known Member
thanks for that reply
so you are guessing its around 20f diff as well. curious now if I want to vape at 360 I suppose I should be setting it to 340.
AirVape Legacy Pro
- Thread starter JohnJacobs
- Start date
so you are guessing its around 20f diff as well. curious now if I want to vape at 360 I suppose I should be setting it to 340.So you’re saying the two tiny paths before and after the glass tube are some industry-standard plastic. Are you using a dental brush pick dry or with alcohol? And will running at max temp for burn off be amother strategy for cleaning them out?The places where material can build up are cleanable, If you still have concerns it's fine, just look for a basic model like the XSGo, that device has every part visiblethere is no magic here, we use industry-standard materials like everyone else.
If you really want to get into every little hole, just use dental brush picks and you will reach eeeevery corner of the PRO.( not necessary IMO)
I'm just gonna go ahead and get some brushpicks and use them without alcohol unless they say you can, I feel like it would scoop out the reclaim pretty well without any alcohol, maybe not every last bit but I'd imagine more than enough for it to function properly, but with plastic/rubber anything I am cautious with how long and often I expose it to alcohol. Obviously I'm not worried about the silicone pieces that are easily replaceable like around the screen or dosing lid, but for the gaskets around the glass tube I'd worry a bit more.
I'm also still really enjoying this vape by the way.
Hi,
Sorry, it was a long weekend for me
Battery: I will ask the dev. team today.
Cleaning: I use a 6mm dental brush to clean every corner of the PRO. I like to start with a dry brush, get off all the dry stuff, and a little alcohol after. Keeping it only a short time on, and use a paper towel after. it works for me.
I get big clouds in on demand you just need a long ass draw, but I get bigger hits than session with a long steady draw, basically kill it in 3 hits
Shorner
Well-Known Member
Are you drawing fast or slow in on demand?
Temp stepping is required plus an initial sip to draw.
Vapour is v cool. Im yet to do a brief write up just a bit unwell atm
Newbie initial experience and questions: I’m doing a slow and steady 15 second draw carried over from my DynaVap technique. I’m not temp stepping, but just starting to hit before the vibration. Cool and terpy. Yum!
Whoever suggested using a Mighty screen as a bowl reducer and to reduce mess: yes this definitely works for me! After just 3 sessions the built-in bowl reducer is so sticky that it spins around when I’m brushing it off; so it’s no longer adjusted to the same spot and fails my “too much fiddling” test.
Whoever suggested the temp reading is about 20 degrees below actual: that fits my experience so far compared to vaping with my Mighty. And the starting temp reading at power-up is 20 degrees below room temp. Is that common or have I got a lemon?
Whoever suggested using a Mighty screen as a bowl reducer and to reduce mess: yes this definitely works for me! After just 3 sessions the built-in bowl reducer is so sticky that it spins around when I’m brushing it off; so it’s no longer adjusted to the same spot and fails my “too much fiddling” test.
Whoever suggested the temp reading is about 20 degrees below actual: that fits my experience so far compared to vaping with my Mighty. And the starting temp reading at power-up is 20 degrees below room temp. Is that common or have I got a lemon?
Last edited:
Kind of in the middle, I'm pulling into my lungs from the diaphragm.
RxPlorer
Well-Known Member
I think it's common and I don't think there's any adjustment to the sensor reading. @Gary-Airvape is there a plan to calibrate future batches?
MagnumMafia05
Well-Known Member
No one found any dosing capsules from other another company that works yet?! 
Shorner
Well-Known Member
[/QUOTE]
Cheers mate,
Cheers mate,
This is what i have been doing with a business card.To avoid messy fill-ups, and still waiting for a dosing capsule for the legacy pro, i use a small cardboard bend in V shape as a funnel. Then i place my "botanicals" on it and drop it slowly in the oven...
That's way less messy than with my finger-tips
Okla68
Well-Known Member
Has anyone noticed that the air Inlet screen on the bottom of the Legacy is perforated with holes the same shape as the Apollo Emblem ? Nice design touch, IMO.
(Just a Medicated observation, lol !)
Mr EFF,....Yes it will fit ! Will also Bend Very Easy trying to remove from the OG !
(Just a Medicated observation, lol !)
Mr EFF,....Yes it will fit ! Will also Bend Very Easy trying to remove from the OG !
Yes, it will fit ! It will Bend Very Easy trying to remove it from the OG ! BE CAREFUL !!!
Last edited:
We will have a look at it!
Thanks. For a fixed 20 degree error it isn’t too hard to compensate. But if it’s a 28% error, that’s a 100 degree offset at a 360 degree setting. So not really functional. So far it seems somewhere in between
MagnumMafia05
Well-Known Member
anyone think the mighty capsules would work? I can't find measurements on any dosing capsules.
Last edited:
We have the first prototypes of the dosing capsule, and it will come shortly! with a proper loading tool/funnel.
Shorner
Well-Known Member
Great, send me out a tester if you like lol !!
Orvaxxx
Well-Known Member
They fit but you can’t close the lid.