Search results

Search for the part numbers - my nozzles arrived from eBay this morning And all's working well with about 115 x 3mm rubies, a slightly flattened out Arizer dome screen at the bottom and a bigger screen in the top Really pleased with the results and fit with the Elev8R, short 18mm reducer...

8 - 15W max You could power a buck boost controller from a wide range of sources that you could charge with the solar

The lil bud (and its siblings) had a version of Alan's spiral mesh coil too https://fuckcombustion.com/threads/lil-bud-by-vapwood.25789/page-99#post-1349236 I don't think I've seen any longer ones than these on sale https://www.fasttech.com/p/9665849 I've always thought we should be able to...

Yes ... and a few other undesirable possibilities

I've not taken one apart but I'd say it should attach to the metal handle part as I have taken a few soldering irons apart (which are very similar things) and the earth wire goes to the metal around the heater to protect the user in case there's a short

I use them with all my buck boost controllers I'm a little surprised REFC hasn't included some provision for one in the design to be honest And think a higher rated rocker switch in the housing would be a better option

Add a switch ??? https://www.amazon.co.uk/Extension-Switch-switch-Cameras-Connector/dp/B07CFWG3DJ

Nice builds :tup: Really pleased to see a few more DiY Glass Symphonies on the board Yes (well no actually but I know what you mean :) ) In the listings they say it's a K type thermocouple You could test that if you wanted Holding the > button for a few seconds on start-up will auto tune...

I've not got one to check but I would probably just wrap the quartz with a strip of aluminium kitchen foil to fill the gap

The element is connected to a 936D soldering iron controller for temp control so I did know the answer to that :) Can't remember how much now but temps are lower and it hits harder with the balls

Yes - I use 2.5mm rubies in my LSVlog

Yes - these are the ones I use The second one should fit nicely in an REFC labs ATM module ..... https://fuckcombustion.com/threads/the-advanced-telemetry-module-by-refc-labs-the-worlds-first-advanced-precision-multi-core-capable-desktop-heater-controller.51998/ I think he uses this one...

The smaller Vapocane came with one I think bowls like the herbo, terp torch or hot rod will put the heater too far away from the load with an 18/14 adapter but an Elev8r bowl with an 18/14 adapter may work E2a The ddave concentrate chamber...

VROD or 19/26 Glass Symphony on the 18mm rig Elev8R enail or Halo Whippi3 (like an iDB Halo) on the 14mm rig Splinter Z or Vapcap for direct draw QQ4V or VROD for rosin

Yes - with a glass honeycomb screen If I can find one

I have been using one of these for the screen in the 24mm bowl https://blackleaf.eu/steel-hanging-sieve-oe-15mm which seems a bit silly to be honest as it's all glass up to that point altho you can just bend the metal tab and push it in and it stays in place when you tip the bowl up Does...

I dare say they have but I don't recommend it The Liitokala batteries on AE are commonly sold as fake hg2, 26A, 30Q ... etc but the specs are never the same as the real thing so you gotta ask yourself if it's really worth the gamble to save a couple of bucks

I hope I'm wrong but it looks like another rework station in a new case for a 10 fold mark up, to me. Maybe this one again? https://www.wagnerspraytech.com/products/heat-guns/furno-500/ Like the TochiTorch

19/26 3 way claisens https://www.aliexpress.com/item/32733971710.html? https://www.ebay.co.uk/itm/14-19-24-29-Joint-Distillation-Adapter-3-way-Claisen-75-Head-Connector-Tube/172602788270? Shop around as there are loads available and ideally you want the side arm higher than the one pictured in...

Yes but the TCR is the rate of change soooo if you then increase or decrease the temp by 10 degrees and judge if it's actually gone up or down 10 degrees. the temp will change by more than 10 degrees if the TCR is too high and less than 10 degrees if the TCR is too low. I like to set the TCR a...