Search results

I thought strain too at first but he did mention it was acting up turning off and won't turn on now... Try a "soft reset" (search and check "this thread only"), the "hard reset" is taking it apart, pulling the battery from the unit, pressing buttons, and reattaching the battery.

If he collected them all he could make a new water attachment!! Solo got me like :lol: eating at a restaurant like I'm not the highest motherfucker in here :science:

down to the draw tube on draw tube for vapor transfer.

I always use screens. With properly ground and dried material you can start as low as 2, which I usually do. The taste is amazing and then you still have 3-7 to get through!

7-8 full cycles is what I got when mine was new. Sounds pretty normal, what with the "1 session per LED" guideline.

You'll want to work it into smaller pieces for more surface area, perhaps a little bit of bud on the bottom and a layer of hash on top. Maybe a bit more flower over the hash?

I don't see a Solo, Vapman, Underdog there?? ;)

Purple Kush, not a lot of purple throughout the nugs but it's got that purpy terpy :drool:

You can keep it on the plate, cover it with cheesecloth or something similar so no dust/particles float on it. Cool dark place is fine after evaporating. There's a reason we're talking about making ejuice with EJMix or skipping it and using RDA's to vape oil instead of VG/PG, the solubility in...

Vaporizing is not a form of combustion. http://en.wikipedia.org/wiki/Combustion http://en.wikipedia.org/wiki/Vaporization

That's called furnace cement, it's there because it can handle heat and being heated over and over again. You're not supposed to remove the screws there, I don't see any situation in which I would ever have to do that. Maybe even warranty-ending. Blue or green corrosion on terminals in a car...

I can take single hits through my water pieces with my Solo and end up coughing and sweating :shrug: Haven't smoked in so long, used to smoke cigs too but now even the smell of them is off-putting.

No but my stems all aren't perfectly flat where the rim of the "business end" is, it's not so uneven that I can see it with my bare eyes but if I feel around it or sit it against something flat I can tell. It needs the little bit of unevenness otherwise it would sit flush with the four air...

turn the solo on, once it's done with the light show, hold the left button down for a few seconds. you should hear a confirmation beep. hold it again for a few seconds and you won't hear anything but it will turn the sound back off again.

Glass screens will work for that, I'm not sure which kind @KidFated. is using but that's what he uses them for. We were talking about flat "tophat" like screens. Looks like the one on the right http://fuckcombustion.com/threads/the-arizer-air.16415/page-67#post-715810 except you will want to...

I did too! Then I realized the stupid ring holding the chain inside the water tank busted :\

If you're getting it from PuffItUp Randy and the team will take care of you.

I'm not currently currently vaped, but I did eat some edibles I made with ABV. Hoping I was able to do this properly, I was aiming for mostly CBD/CBN and added about 10 grams of lightly vaped material... total was around 44g dry and all that came out was about a cup of dark dark dark green...

it's a screen made out of glass, they come in different shapes like daisy flowers and jacks as well as little circular ones with holes. Local headshop, might run you a buck a pop or so, a fair bit more than regular metal screens. I would not advise dosing somebody with any sort of drug that...

They may be rated for 450 (IIRC) but I wouldn't put them in the stem. If I want to make a shorty stem I just use a screen. Usually a 1 inch, press it into the stem and form it to the inside and against the walls/floor and corner where they meet, take it out and trim to height. Then flip it...