Search results

Yea, I use and toss them. I don’t notice any difference in airflow honestly. Wish they were a little bit better quality like the stock though.

I've stepped up the flame since first trying out with good results. Started small, 30 + seconds, pulling away at the 2nd click (after break in period). Went with the big buddy for the quick 10ish seconds, and pulling away before the first click. That works just as good imo. Now using a smaller...

You won’t need to if you go with the 9mm ;)

I use my finger nails to get a small bud size for good extraction. The BCG coarse grinds some of it down too much & particularly it’s dryer herbs. The 18 is a tad big for those buds so it’s the only one I use with a screen. I’ll also do a very light push down with a wooden poker a couple times...

Along with this, I think the screen will start to form and cooperate more with some use & heat ups if I remember correctly. Nice write up @jaanky , setup looks sweet! The bowl length has been shortened too. Would be nice with a native 18mm connector though.

You can see them in the hole on top of the cap. It doesn’t move very much and happens so quickly it’s difficult visually to tell. Yea, they’d need to be in the vape too for my worries. Guess if you didn’t wash hands after handling.. yada yada.

Yea this is coil fit with my newer one piece. Works fine, but tough to get on. Don’t have a handle yet.

That would be nice! Glad mines not too bad and still usable. I’ll throw it back on from time to time but this Omni MP is one of my favs and so comfortable :nod:

@RogueGuy did you sell all the handles you had listed? My QC slides in & out of the coil pretty smooth, but my Terpcicle fits in squeaky tight. I’ll probably do a QC wireless option once you get the stand/holder available as well.

Yea, carb is covered for most of the session. I’ll let a little bit of air in the mix when needed.

That’s how the XL dyna condenser sits in my wooden stem too. Found my Omni condenser and mouthpiece also fit (yea!) and that’s even further away. It’s going to be hard to get anything going without covering the carb (at least initially). A different feeling pull for sure but I’m getting used to it.

Yea, pretty uncommon config. I personally like the bigger tubing for this rig. I’ve got a few DH ones, but usually end up using the TAG (2nd quality) that are better made imo. https://www.thickassglass.com/products/drop-down-adapter

@Spy Car while you’re shopping, you should snag a 18 to 14 simple reducer like THIS in case a drop gives too much restriction for your preference.

FC-199 maybe? It’s been awhile since I’ve had the ZX on it, perhaps a bit big, but think it’d suit what you’re looking for. https://www.dhgate.com/product/70mm-hookahs-bigger-vaporizer-swiss-bong/852316893.html

Agree! :brow: I’ll load enough for a couple pulls at 35-40 degrees lower on the reading. Abv comes out very light, but well spent.

I threw mine back on the Dovetail stem after it was in need of a good cleaning and set aside during a lot of wpa activity. This time left out the inter-cooler that was sliding around and wow, what a difference. Around 6-7 nice & easier pulls on a full bowl. :o Unfortunately chipped the MP with a...

10mm Nice ;) I’m still liking boro on top of zirc in one of mine.

A quick tasty rip with the CC setup 😋 This drop down is making things real smooth on various rigs.

Right on. Need some balls in there for cooling unless it’s going good without. I was used to no carb with the wood, so awkward when I first got my glass stem too. Now letting a very quick & tiny amount of air through it, a couple times during a long draw.

Nice! Yea the thinner walled heaters are a bit more sensitive (under cook vs over cook) than the bigger boys, but very rewarding & flavorful. Often times I’ll add more heat while pulling as long as I won’t burn my face with the setup I’m using. Enjoy :brow: