Search results

You could squish that hash into rosin with a hair straightener and which would allow you to use a much more compact on demand wax pen instead of a larger flower vaporizer.

That's interesting, I find the heater does get overwhelmed to the point I can clear my draw simply by breathing faster at the tail of my inhale. I only get a fraction of the vapor density/output if I rip my rig as hard as possible compared to ripping it as slow as possible (uncapped)

That's like bare minimum temp for the FP IME. You can easily go 100-200 degrees higher if you wanted bigger rips.

This is a popular thought in the concentrate community. I do believe the reduction in air does reduce the pressure, but I'm not quite convinced it's to the point that a vacuum effect sufficient of reducing vaporization temp is occurring. (on any meaningful scale) If you really wanted to pull...

With the Showerhead, I don't really find there to be more heat, When doing a flower toke the carb cap is not functioning in the same way it does for an oil hit. IMO with flower, using a carb cap throttles back the rate at which air passes through the heat exchanger and simply heats the air to a...

With my SOL rig, I find if I put both lips against the flat mouthpiece, it takes more pull to fire and I don't really like it, whereas if I shift my lips down a bit and put my bottom lip slightly under the mp it forms a seal a lot easier IMO and doesn't feel like I'm breathing through my nose...

This one seems like a killer flavor saver, that perc is nice and low, looks like it will function with very minimal water. https://www.dhgate.com/product/ccg-toro-dabber-rig-with-gilded-slitted-cut/412168763.html#cart_view-3-null

A trigger clamp? That's a great idea! I think I might have one laying around from my first foray into rosin, a Hash Masta Kut trigger clamp press!

@biohacker amazing setup bro! :rockon::rockon::drool::drool::borg::borg::rockon::rockon::sherlock::sherlock: Love that LED display! Where's your ABV jar? :rofl: :cheers::cheers:

IMO with the Showerhead you can use a lower temp + a carb cap, or a higher temp and no carb cap. It's the same end result.

You could even get the D-nail wraparound and run it without a dish until you have the money. Lots of options, either way I think you're gonna love it!

FWIW I don't think the ball bearing type dab inserts are gonna do much with an enail. It does add thermal mass when doing torched dabs, there's a bunch of quirky ones out there but I'd rather just hook a coil up than mess with all that extra gear. Torch dabbing has way too much gear.

Check out Mayoral Quartz. Pretty sure they do custom.

Didn't realize they made a fully opaque quartz insert, that's interesting.

If you put the dirty bud in a trashcan and leave the lid on for 10 years the pesticides should go away. No but really, I'm not aware of any real form of pesticide remediation short of a distillation with advanced chromatography, but even that is questionable IMO.

Look for something with a recessed joint (dewar) for the lowest profile. 10mm female for standard vapcap mouthpieces, 14mm female for Vong bodies. You can also use a 14mm to 10mm reducer to fit those mouthpieces.

Well your medium and my medium could be completely different sizes, so it's hard to say. That said if I was going to dab anything bigger than "small" I would go for the D-nail for more surface area as it will allow lower temps and be easier to land the dab. I'd rather use the D-nail carb cap...

Agreed! Some of those ghost hits have a very spacey stone!

IMO you could save about half that much if you just went with the basics, but I'm sure it's a great kit. Yes the Dnail wraparound is a bigger dish, though if you are trying to be more efficient with material it's probably better to stick with a smaller dish. The FP could be very efficient...

In my experience since you're only vaporizing a reduced portion of the cannabinoids, the only way to really increase vapor density is to vaporize more material at once. That's why I prefer a desktop for flowers. IMO no vapor output at 330F is going to be that impressive without some solid LED...