My NANO will get one MAX FLIGHT!
Does the member who reports loading .1g have a scale that's accurate to within .01g? That's what would be required to accurately weigh .1g. Personally I wouldn't be trying to load .1g in a nano stem. It's just too much.
You'll get it figured out. Just takes some practice. You don't have to have an exact amount loaded nor do you have to load the same amount all the time. My loads vary and I just deal with it by adjusting the temp dial appropriately.I am still struggling with load size / screen distance / restricted airflow , argh
I've been medicating for scientific reasons these days ;D
...and because i love medicating with cannabis as much as you do
I just cannot figure out how to put 0.1 into the gong?!
May I ask you which distance (from the screen to the heater core) you choose when vaping 0.1?
If I use the fixed gong (or the adjustable one with the screen set to about 15mm) I find it impossible to fill more than maybe 0.04 without touching the heater core. And even with a load like this I regularly charr the top of my load because it's too close. I try to flatten out the top with a glass poker, but this always ends up in a restricted airflow, which I don't like at all.
I am still struggling with load size / screen distance / restricted airflow , argh
I go by feel mostly.I've been medicating for scientific reasons these days ;D
...and because i love medicating with cannabis as much as you do
I just cannot figure out how to put 0.1 into the gong?!
May I ask you which distance (from the screen to the heater core) you choose when vaping 0.1?
If I use the fixed gong (or the adjustable one with the screen set to about 15mm) I find it impossible to fill more than maybe 0.04 without touching the heater core. And even with a load like this I regularly charr the top of my load because it's too close. I try to flatten out the top with a glass poker, but this always ends up in a restricted airflow, which I don't like at all.
I am still struggling with load size / screen distance / restricted airflow , argh
It's sunny and warm everyday and we welcome rain!
Same with my state!
It really does work great. I always found my dial spinning over so i couldn't see it, or sliding behind something, got really annoying. Raising it off the ground (table) was the best decision.
I wouldn't expect to get much more vapor from a tiny amount of herb like this. I mean, I can lower the screen and pack more. That works and I get a slightly bigger draw but I have never had a session where the 2nd hit was milking the glass more than the first.
White walling a bubbler is so dependent on the light source. Blow an exhale into a lamp. Makes it look crazy!! Different lung capacities. I grew up on blunts and giant bongs and gravity bongs and other nonsense. Enano beats them all. Lovin it tonight. Baked on some green crack.Hey, thanks for your input @max & @howie105 & @ataxian !
Honestly, it is indeed a lot more comfortable to pack the gong by feel than to weight out exactly let's say 0.1 g. But on the other hand, I have to admit that I am a little nerdy when it comes to this - I weight my doses and keep accounting and so I always have an overview of how much I consume.
So maybe it is irrelevant to know the exact amount of herb you use but what frustrates me increasingly is the fact that I fail in getting long lasting big cloud-draws with my E-Nano so far.
The results I am getting so far are pretty good, no question. It tastes really good, but sometimes I need these big big hits and I have not been able so far to get these kind of hits from my bubbler.
I've tried some different settings, but a normal session for me is like:
I pack a little amount of ground herb in the gong. I just sprinkle it over it, don't pack it. With the shorter side of the e-pick I check that the heater is not touching the top of the load.
Then I put the gong onto my bubbler, the E-Nano's temperature is about 7. I place the Nano onto the gong and wait for like 20-30s before i hit. The glass milks immediately, thick vapor is being produced, but at the point where the bubbler is completely filled (I have a D020-like bubbler) the vapor production stops.
Then i stir the load and get another (mostly) airy draw, most of the time the 2nd hit is unnecessary for me.
Looking at the ABV: I would say it looks okay. But most of the time I find green spots in it. Regularly dark brown ones as well, kind of pre-combusted particles I guess.
So, conclusion: For me, this is normal I would say
I've seen that hundred times on video and basically that is true convection behavior. I know this, since I use several other convection vaporizers as well
First draw - flavor. 2nd draw more vapor, etc.
But unfortunately, I am not able to get a session like this.
I spend exactly the same amount of herb like before, and that frustrates me a little.
Maybe I was expecting wonders, I think I was, yes. But when i read things like "0.025 gave me 4 white walling hits" I wonder what I do wrong here
0.025 gives me exactly ONE hit- maybe a second - read above.
Sorry if this all sounds like a rant, it is definitely not meant to be !!
If I didn't read all these comments about its incredible efficiency I maybe wouldn't have been questioning anything here.
But this at least leaves me a little bit bewildered :-/
Yes this!... i use velcro tape on the back of my dial.
Hey, thanks for your input @max & @howie105 & @ataxian !
Honestly, it is indeed a lot more comfortable to pack the gong by feel than to weight out exactly let's say 0.1 g. But on the other hand, I have to admit that I am a little nerdy when it comes to this - I weight my doses and keep accounting and so I always have an overview of how much I consume.
So maybe it is irrelevant to know the exact amount of herb you use but what frustrates me increasingly is the fact that I fail in getting long lasting big cloud-draws with my E-Nano so far.
The results I am getting so far are pretty good, no question. It tastes really good, but sometimes I need these big big hits and I have not been able so far to get these kind of hits from my bubbler.
I've tried some different settings, but a normal session for me is like:
I pack a little amount of ground herb in the gong. I just sprinkle it over it, don't pack it. With the shorter side of the e-pick I check that the heater is not touching the top of the load.
Then I put the gong onto my bubbler, the E-Nano's temperature is about 7. I place the Nano onto the gong and wait for like 20-30s before i hit. The glass milks immediately, thick vapor is being produced, but at the point where the bubbler is completely filled (I have a D020-like bubbler) the vapor production stops.
Then i stir the load and get another (mostly) airy draw, most of the time the 2nd hit is unnecessary for me.
Looking at the ABV: I would say it looks okay. But most of the time I find green spots in it. Regularly dark brown ones as well, kind of pre-combusted particles I guess.
So, conclusion: For me, this is normal I would say
I've seen that hundred times on video and basically that is true convection behavior. I know this, since I use several other convection vaporizers as well
First draw - flavor. 2nd draw more vapor, etc.
But unfortunately, I am not able to get a session like this.
I spend exactly the same amount of herb like before, and that frustrates me a little.
Maybe I was expecting wonders, I think I was, yes. But when i read things like "0.025 gave me 4 white walling hits" I wonder what I do wrong here
0.025 gives me exactly ONE hit- maybe a second - read above.
Sorry if this all sounds like a rant, it is definitely not meant to be !!
If I didn't read all these comments about its incredible efficiency I maybe wouldn't have been questioning anything here.
But this at least leaves me a little bit bewildered :-/
