Discontinued Haze Square

Stdudez

Stdudez

Well-Known Member
Oh I was thinking they had implemented the o-rings. My newer mp is much more snug than the one that originally came with my phase 2 unit.
 
Stdudez,
Djsleepy

Djsleepy

Well-Known Member
If they have they haven't told anyone here ...see i had opposite experience...... Mp was still loose....had to do my bump method to seal good.....
 
Djsleepy,
b0

b0

Cloudy...
Djsleepy said:
If they have they haven't told anyone here ...see i had opposite experience...... Mp was still loose....had to do my bump method to seal good.....
Click to expand...

I have to say that when they send me my second unit, they sent as well new o-rings. I told them I had some issues with the old ones and they took care of me.
 
b0,
F

FC123

Well-Known Member
@Haze Vaporizers
Is there any chance, that you will establish a distribution in Europe for service? I know, that you have an agreement with vaposhop but I bought from namastevapes and they only take care for a year. Also they changed it to only half a year nle
 
FC123,
P

Petunia Vanish

Well-Known Member
Petunia Vanish,
C

caseball2051

Well-Known Member
It's a perfect fit on top. They're curved and putting the curved side facing down on top of the load is how I do it.
 
caseball2051,
Vapordeflor

Vapordeflor

Well-Known Member
b0 said:
I have to say that when they send me my second unit, they sent as well new o-rings. I told them I had some issues with the old ones and they took care of me.
Click to expand...
Regarding this, my mp was loose till I removed the ring which is closest to the bottom of the mp, well inserted again and no more fitting problems. In love with my unit! Only downside is battery life.
 
Improvaper

Improvaper

Well-Known Member
Hi folks, first post... sorry it's not a good one.

Received my Square Pro today. Long story short... loose mouthpiece and old firmware. I did a firmware update with a FAT32 drive and when I went to turn it on afterwards, it bricked. No response from any combo of button presses or plugging in. Is RMA and waiting my only option?

Thanks for any advice.
 
Improvaper,
Djsleepy

Djsleepy

Well-Known Member
Improvize said:
Hi folks, first post... sorry it's not a good one.

Received my Square Pro today. Long story short... loose mouthpiece and old firmware. I did a firmware update with a FAT32 drive and when I went to turn it on afterwards, it bricked. No response from any combo of button presses or plugging in. Is RMA and waiting my only option?

Thanks for any advice.
Click to expand...

PM Haze from here.....best advice I can give you....:tup:
 
RogueGuy

RogueGuy

Well-Known Member
Accessory Maker
OK, just got my baby back and I'm not sure whether I should be celebrating or crying.

My square worked great until it just stopped heating. No issues.

Well they sent me a brand new one! This might be awesome or terrible. It started charging right away. I'll let you guys know in a bit
 
MonkeyTime

MonkeyTime

Well-Known Member
Ok, call it what ever you like, but this first hit combustion is bullshit! I haven't kept track and won't, but I'm thinking it's about one pod in 6-8 that get me, and they're all finished in the same session they're started.

Increase my heat up time by 2 seconds to work thru this, but once it's green, I should be able to go, not needing to peer into a screen to see if it's really ready!

I keep starting to get into a rhythm with this thing, and I combust, and it kills it.

Other than that, this thing can rip when it's all aligned and clean, just increase the haptic feedback a bit.

But please, no more combustion :puke:
 
MonkeyTime

MonkeyTime

Well-Known Member
Vapin in the usa said:
It would help to keep the light on the color (temp) your set too, from the now permanent Default blue
Click to expand...

I'm not sure if this was directed towards me, but I know my temps, it's all good. I see benefits to the lights as they are now, and with what you're suggesting, either works for me.

My issue is solely with the heater firing at max past it going green, it's instant combustion, something a regulated vape should not do unless I use an excessive temp, I don't.
 
buckhakeesah

buckhakeesah

Well-Known Member
Even though this is a regulated vape, I treat it like an unregulated one when using it. Drawing and sensing the vapor a few seconds before it should go green helped my experience with the square and helped me avoid combustion on the very first hit.
 
Y

Yannik

New Member
Has someone else also problems with the app on windows 10? Mine can’t get found , I tried every USB port. Always just the simulation.
 
Yannik,
Jill NYC

Jill NYC

Portable Hoarder
Yannik said:
Has someone else also problems with the app on windows 10? Mine can’t get found , I tried every USB port. Always just the simulation.
Click to expand...

stickstones said:
Did you turn the vape on? I start the program, plug in the vape, then turn the vape on and it recognizes.
Click to expand...

And just because the light is blue when you plug in, doesn’t mean it is turned on. You must physically turn it on before it will be recognized.
 
b0

b0

Cloudy...
I know they have mine because of the tracking so should be in the way back soon!! Guess they waiting to know what the issue was before confirming with me they got it.
 
b0,
ginolicious

ginolicious

Well-Known Member
Brought this thing up to the chalet for a bachelor party over the weekend. Stars were not aligning for my boys. I had a fine grind, full pod, tamp down and set at 430. I think only 2 hits were decent out of the 4 pods. Battery drained super quick too. So I’m not too sure. But people were not impressed with it.
 
ginolicious,
ginolicious

ginolicious

Well-Known Member
In my defence though, I only did iso wipes on the oven lids and the pods. I did not do a deep clean and clean between the screens. Thinking that may be the culprit. But unit still needs 1-2 prime hits before getting nice big ones.
 
ginolicious,
You must log in or register to reply here.
Top Bottom