That's what I began with. Although, today I lowered to 380 to begin (in hopes of getting an extra session out of the capsule) and it didn't seem to diminish the cloud. Gonna try to start progressively lower - to see if that works.
POTV Lobo
- Thread starter Finessseee
- Start date
Puddentain
Well-Known Member
My preference is just a bit lower, at 384, after a quick step up from 350 for a bit of max flavor. You’ll have fun figuring out your favorites. The Lobo extracts pretty efficiently.
Blackbeen
Active Member
Is there a full manual anywhere? the the paper quick guide points to totv.life/lobo but there is only another even lesser quick guide found there.
Stupid question but what makes this part convection if no fan is employed?
At first glance I really like the design/dosing caps, waiting to charge for burn off.
Stupid question but what makes this part convection if no fan is employed?
At first glance I really like the design/dosing caps, waiting to charge for burn off.
Old Stoner1958
Well-Known Member
When you inhale the convection come into play.
I removed mine. Didn't see the purpose since I only use the caps.
They're just extras for when the included screen gets frayed or damaged over time. They're for the spot underneath the bowl cover.
The fat mesh puck is what's for the dosing caps, it's the concentrate pad
The 'fat mesh puck' isn't used with the dosing caps. Unless I am misunderstanding you, they both won't fit at the same time?
Old Stoner1958
Well-Known Member
The concentrate pad goes inside the dosing cap
Ahhhhh. Didn't know that. Thank you!
Old Stoner1958
Well-Known Member
I believe this has a more agressive heater. It will extract much fasterr
Blackbeen
Active Member
Yeah, I'm kinda a slow to draw, lite user, I don't know how I'm gonna time this, never been one to worry about battery life but this looks like has 40 minute max, might have to shut off between short session draws or something.
Old Stoner1958
Well-Known Member
You should get 10 four minure sessions.....plenty of battery lifeYeah, I'm kinda a slow to draw, lite user, I don't know how I'm gonna time this, never been one to worry about battery life but this looks like has 40 minute max, might have to shut off between short session draws or something.
Blackbeen
Active Member
Does that come apart? if it does I can't figure how I would change that screen.
Push it up, not down. Through the top towards the mouthpiece.
Last edited:
Use the little dab tool they sent you a long with the Lobo. Take the mouthpiece out of the part, then stick the tool down and gently push on the screen. It'll pop out.
After some time this screen gets really sticky from the vapor condensing on it, so it's easiest to take out right after using it so the oils are all melted
Blackbeen
Active Member
Yeah, finally figured that out, used a broken wifi antenna, with the short session time is it good to hit as soon as it reaches temp? I'm used to giving them a few minutes warmup time.
Jojofernz
Well-Known Member
With the Lobo, I’m able to start hitting right when it hits temp and get vapor.
I’ll sometimes hit it as it’s heating up to get some flavorful first rips
Mr. Natural
Have vape, will travel
The Lobo is a beast at extraction! My typical session consists of 3-second DTL pulls, with temp setting at 400 F. The first pull is at 325, then around 360, and ending at 400. Power off, and use the residual heat for another 3-5 pulls. I get 2 sessions per lightly-loaded capsule with this technique. Tobacco-brown AVB, and no coughing.Yeah, I'm kinda a slow to draw, lite user, I don't know how I'm gonna time this, never been one to worry about battery life but this looks like has 40 minute max, might have to shut off between short session draws or something.
Blackbeen
Active Member
Yeah I would likely go that hot on the the Solo II it's 390 unless Kief or something is involved 420/450 for the Arizer XQ2, it gets too burnt at higher temps IMO.
tgvp
Well-Known Member
After some search, I finally found a friend going to visit someone in US and willing to transport a device for me on the return trip. Unfortunately, when I tried to order a lobo to be shipped at his guest address, I stumbled on the age verification process 
I need to provide the last 3 digits of the SSN of the guest and as I understand, that's kind of a sensitive data, so as I don't personally know the person I haven't asked. But there is another solution, maybe.
Do any of you know a physical shop in New York where my friend could buy the Lobo for me?
I need to provide the last 3 digits of the SSN of the guest and as I understand, that's kind of a sensitive data, so as I don't personally know the person I haven't asked. But there is another solution, maybe.Do any of you know a physical shop in New York where my friend could buy the Lobo for me?
krvnked
Active Member
The gang is all here
Thanks delta 3d studios for making awesome products and helping me round out my collection for all my products
Thanks potv for a two year warranty hopefully I never have to use it
I really can’t picture myself needing to buy any more vapes or accessories any time soon, I consider this an end game setup
Blackbeen
Active Member
Yeah, this much different than I'm used to, very fast (almost too fast) extraction, in order to get a flavor hit I have to draw at around 200-250F set to 385/90. 4 fast heavy hits & its done, I defaulted to a whip with arizer xq2 but it's too harsh with the Lobo so I started using the bubbler.
Seems like I tend to use (or maybe overuse) more weed with it as it extracts so fast but I have plenty so its not an issue.
I started out at max 6 minutes timer but ended up knocking down to 2 as its just not needed on one cap & I definitely need some extra caps to rotate.
krvnked
Active Member
“Babe don’t disturb me when I’m using the cushion whip”Yeah, this much different than I'm used to, very fast (almost too fast) extraction, in order to get a flavor hit I have to draw at around 200-250F set to 385/90. 4 fast heavy hits & its done, I defaulted to a whip with arizer xq2 but it's too harsh with the Lobo so I started using the bubbler.
Seems like I tend to use (or maybe overuse) more weed with it as it extracts so fast but I have plenty so its not an issue.