-
SCAM WARNING! See how this scam works in Classifieds.
Phase3 Vaporizers
- Thread starter invertedisdead
- Start date
Pukka
Well-Known Member
Call the USPS customer service 800 number and complain. It took me about 5 years of being "that asshole customer" to finally get them to deliver my stuff where it belongs. YMMV.
Also, if your mail's delivered to a community stand box there may only one box per stand for packages and it may already be full with someone else's delivery. And your mailperson's too lazy to drop it at your door.
coolbreeze
Well-Known Member
I've had this happen a few times and in my case it's always someone rushing to get their route done so they fake it and bring it the next day. Hopefully this is the case for you, too. But I would still call, maybe they can nip it in the bud for next time.
w00t! Me too!
Pukka
Well-Known Member
Me three!
4-Aces King-High
Well-Known Member
Me 4 ,just got shipping Notice For the 3-position bowl. My ZX bowl has been lost in the house Or Put away mistakenly with Other devices for several months now And sorely missed.Thanks To Ryan I will enjoy my he ZX once again,Cheers.
yea thats my hope, i did call they have no clue right now so we'll see, they did say its not my normal carrier on the route today too so maybe that has something to do with it even
Pukka
Well-Known Member
You'd have to measure and ask (their reddit is very active) but it looks like Rogue wireless handles might work or be tweaked to work ...
You just turn it gently against the curve of the coil. You are just looking to make it a bit more loose, not to bend it. You could also wrap some blue painters tape around your ZX to help stretch it. Some folks use non-marring pliers but I just used my hands.
Fearless Disaster
Well-Known Member
My ZX just landed, and at the same time as my first ash catcher! I cleaned everything in iso and water and assembled the zx. its currently heating to 500F while i figure out what to do next. Is there any special cleaning that I should do? the pid was set to over 700F but i didn't let it get that hot since I don't know what I'm doing lol.
assuming theres no further cleaning i need to do, can someone suggest a starting temperature? On my CH Mercury/Shovelhead I have been using 525 - 535. Whats a good temp for what you feel is a pretty full extraction? I know there will be a range of answers and that is valuable to me as I step into the unknown <3
bizwaxzion
Enigmatic Cannabist
I'm at 565F on the PID it came with.
letter never sent
reckoner
Yeah I would start at 500 and adjust from there. I’m typically around 520 when I use mine. I find a good balance of flavor and vapor at that setting.
Fearless Disaster
Well-Known Member
thank you! i started at 500, then 525, 550, and had just turned it up to 560 to try. I've just bumped it to 565. I find that with a new device i need to see how high i would ever want to push it before i can back it down to lower temps. it is amazing so far!
PurpleHaze1911
New Member
Do anyone know if the new 3 position ZX Zirconia chamber now come with the 14MM pre order.
Looks like the ZX is still available for pre order. My question I do I need to add the $100 chamber to my order.
I believe I saw it now comes with but I’m unsure.
Looks like the ZX is still available for pre order. My question I do I need to add the $100 chamber to my order.
I believe I saw it now comes with but I’m unsure.
They do yes. They cone with a bowl standard. If you tick the box you will ne adding an extra bowl. The bowl will be the 3 position.
Fearless Disaster
Well-Known Member
OK! I am out of town for a week but before leaving I got a day to test out the new ZX in the context of microdosing. TLDR the ZX is amazing for microdosing. You all already knew that, I did not. @El Duderino I would be curious to know how the ZX meets your microdosing needs!
Here are 5 piles of AVB. All were vaped at 565F, one hit extraction with a cleanup hit. On the top row are my initial tests, just using my microdosing scoop. Since some vape designs fall apart with small loads, I started with approx a 50-60mg load, then a 25-30mg load. both vaped to the same shade, so I went ahead and busted out the scale for science. In the bottom row are three piles: 10mg, 25mg, 50mg. In my microdosing experiments 25/50mg seems to be a good single/double dose for me, but I wanted to be able to vape down to the resolution of my scale because science. You can see that the 10mg pile is the the same shade as the biggest pile at the same temperature. To me this shows the strength of the ZX design. It will be a week before I can play with it again but from my first day of testing the ZX is everything people say it is for microdosing. The only other device that I have that will vape down to 10mg while still delivering a satisfying ohe is my Tempest.
For reference, here are the before and after bowl shots for each of the three weighed tests. Pardon the funky angles. I used a high CRI 219B 4500K flashlight to get the most accurate color reproduction and working with the light, phone, and shadows was a bit challenging:
Here are 5 piles of AVB. All were vaped at 565F, one hit extraction with a cleanup hit. On the top row are my initial tests, just using my microdosing scoop. Since some vape designs fall apart with small loads, I started with approx a 50-60mg load, then a 25-30mg load. both vaped to the same shade, so I went ahead and busted out the scale for science. In the bottom row are three piles: 10mg, 25mg, 50mg. In my microdosing experiments 25/50mg seems to be a good single/double dose for me, but I wanted to be able to vape down to the resolution of my scale because science. You can see that the 10mg pile is the the same shade as the biggest pile at the same temperature. To me this shows the strength of the ZX design. It will be a week before I can play with it again but from my first day of testing the ZX is everything people say it is for microdosing. The only other device that I have that will vape down to 10mg while still delivering a satisfying ohe is my Tempest.
For reference, here are the before and after bowl shots for each of the three weighed tests. Pardon the funky angles. I used a high CRI 219B 4500K flashlight to get the most accurate color reproduction and working with the light, phone, and shadows was a bit challenging:
Last edited:
PurpleHaze1911
New Member
Just placed my pre order for the ZX. Now the patient wait begins. Looking forward to it