Carb-Bubble-Spinner caps-where do you place yours when hot?

[CrazyDiamond]

As the title says, I'm looking to see how and where you put a hot carb cap right after you dab...looking for better ideas than I have below.
Right now I'm using an 18mm male flower bowl turned joint side up and I let it sit there to cool.

 

[Shit Snacks]

Quartz Pi 30mm bubble cap has a large enough base ring at the top so I can set it on the table upside down without issue... Plenty stable as long as you don't knock it over lol

710 coils and 510 mod both sell little 3D printed cube that can hold them as well, I've seen fancy wood ones and resin ones too...

 

[CrazyDiamond]

Ya I've seen those, the Glob-Mobs are nice. I've seen a bunch on Etsy that are just plastic, no good for heat. Some are plastic with a silicone o-ring, and one guy there, ascendingtom, makes them with a full silicone insert for $10 a piece.

I was wanting to see if there are some other methods, kinda like I do with the upside down bowl, lol.

 

[Shit Snacks]

Ya I've seen those, the Glob-Mobs are nice. I bunch on Etsy that are just plastic, no good for heat. Some are plastic with a silicone o-ring, and one guy there, ascendingtom, makes them with a full silicone insert for $10 a piece.

I was wanting to see if there are some other methods, kinda like I do with the upside down bowl, lol.

Haha yeah I bet there's all sorts of DIY ideas! I think it's rush valley studios on IG that makes the wood ones, not cheap though, like $45? Burls... Probably can get cheaper from another woodmaker here I'm sure... Oh! Just get these ceramic toothbrush holders:

https://www.amazon.com/JCBIZ-Toothbrush-Accessories-Organizer-Multifunctional/dp/B0792Q5YSR/ref=asc_df_B0792Q5YSR/?tag=hyprod-20&linkCode=df0&hvadid=242003408293&hvpos=&hvnetw=g&hvrand=9294758263791681813&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9030954&hvtargid=pla-430397073011&psc=1

 

[arb]

The lid to the Ssv glass jar.
Popped the rubber gasket off and its perfect.

 

[CrazyDiamond]

That's what I'm talking about! Some out of the box stuff like a ceramic toothbrush holder...nice.
And an SSV glass jar lid...whatever and SSV glass jar is, lol.

 

[FlyingLow]

I use a 3x cap stand from GlobMob/710.
Really dig the clean-ability with the silicone lining.

 

[strech]

I use an old broke insert for the bubble cap. The rest have flat surface to just set it down on the dab mat.

 

[CrazyDiamond]

This is what I was talking about that I do currently

 

[Texus]

my bubble carb cap for the Switch fits great in a standard shot glass.

 

[Chicken No Name]

https://www.dhgate.com/product/carb-cap-holder-glass-stand-od-25mm-thick/499334715.html

Have a few of these which are great for the smaller caps

 

[Cheebsy]

The one I'm using most right now sits upside down in the top of my Evo!

 

[Bologna]

I got a couple of these as part of a large discounted 4/20 purchase recently for my more preferred caps:

Carb Cap Holder (Terp Pearl Holder)

Our Carb Cap Holder does a great job of keeping your carb cap and dabbing area clean. It's also a great tool to store your Terp (Dab) Pearls in too!

dabbingwarehouse.com

But I also use cheapo flipped over shorty reducing adapters, too...