Ais vape

iDRINKBLEACH

knowing is half the power - Gi-JOE
It's a rebrand vape but it reminds me of a dotleaf their ig is @aisvape.tech they have multiple chambers. They are not interchangeable with dotleaf unnamed.jpg
 

iDRINKBLEACH

knowing is half the power - Gi-JOE
I actually dont know if this is a rebrand. I misread and they are offering their model for rebranding. I will hopefully have a unit soon so I'll check it out and let you guys know what I think. I'll make sure to do videos.
 
iDRINKBLEACH,
  • Like
Reactions: Severmore

Abysmal Vapor

Saturnine in my mind
Saw it few months ago on alibaba or made-in-china . Any mention what is the chamber housing material ? Looks like 3d printed plastic to me.
 

iDRINKBLEACH

knowing is half the power - Gi-JOE
Saw it few months ago on alibaba or made-in-china . Any mention what is the chamber housing material ? Looks like 3d printed plastic to me.
It looks like it to me. I asked ais and @thevapotorium on ig who just received his. Hes not sure I'll let you know when I'm told. Here's some vids pics from vapotorium ig.
Links were weird I will repost soon at work. I asked him if he would hop on and chime inIMG_20210107_143403_160.jpgIMG_20210107_143405_185.jpg
 
Last edited:
iDRINKBLEACH,

PaperClouds

Well-Known Member
It looks like it to me. I asked ais and @thevapotorium on ig who just received his. Hes not sure I'll let you know when I'm told. Here's some vids pics from vapotorium ig.
Links were weird I will repost soon at work. I asked him if he would hop on and chime inView attachment 5046View attachment 5047
Hey guys I’m thevapotorium on IG. I’ve had my TRIO since Wednesday. This thing is little! The heating chambers are covered in silicon sheaths. They are not glued to the metal in anyway you can actually get a dabber in between them and could probably remove them if you needed to for some reason. There’s is a slight issue with a gap between the top of the oven and the threads that the mouthpiece screws into. This causes material to get in and around the oven if you aren’t super careful and makes it hard to load on the go. I made them aware of this issue, gave them a simple solution and they said they will try and fix it the best they can. That’s really the only issue I have with the unit so far. It gets a surprising amount of vape time out of the 18350. I’ve been doing one heat cycle on green(374f) and then one on red(410f) per bowl and was able to get 4 bowls out of one charge. The 510 cartridge chamber is just that and it works like it should. I didn’t really have enough dabs to really try the concentrate chamber but it it’s a ceramic cup with a raised bottom. It looks like it’s sealed but I can’t tell for sure. The stock mouthpiece fits inside some of the wider/thinner walled, 18mm male joints that I’ve tried. Here is a couple of hits through water. The first is the second hit off that bowl at 374F and the second is the third hit off the same bowl at 410F.

374F second hit


410F third hit

The ABV after 2 hits at 374 and 2 hits at 410 through water.



I’ll keep reporting back about this little guy.
 

PaperClouds

Well-Known Member

This was from an IG story post of mine which why there’s text on it but that also explains the picture. I also talked to AIS and they have no relation nor have had contact with DotLeaf in any way in case anyone was curious.
 
PaperClouds,

iDRINKBLEACH

knowing is half the power - Gi-JOE
@iDRINKBLEACH Nice review. Colored silicone max safe temp is 213C , I know that from the Ghost green silicone fiasco. At least those guys dont let you run it over the safety specs.
Yeah I feel like they really took a lot into consideration with materials it was built with and capping the heat where they did. The oven seems like a tank compared to others with same ovens. I feel like it would appeal to masses more if it could go higher safely but as I stated that’s a bias opinion because it’s what appeals to me.. It has its niche for sure though. Thank you man appreciate the kind words.
 
Top Bottom