-
SCAM WARNING! See how this scam works in Classifieds.
9mm Male 8mm Female Adapter?
- Thread starter GitRekt
- Start date
GitRekt
Well-Known Member
Do you know what size o rings would work?
Papa Lazarou
Member
Bumping because I’ve been unsuccessfully searching for the same…
I have no doubt I can help make what you need, but I'm having a hard time trying to picture what you need. Can you (or someone) send me a draft a rough sketch of what you need? Preferably with measurements so I know what dimensions I'm working with.
I'd likely make the part using surgical grade stainless steel (probably wouldn't cost more than $15 for a small adapter), or I could work with one of several different glassblowers depending on the needs.
You can fill out a custom request form on my site, or shoot me a private message here- let's make it happen
I'd likely make the part using surgical grade stainless steel (probably wouldn't cost more than $15 for a small adapter), or I could work with one of several different glassblowers depending on the needs.
You can fill out a custom request form on my site, or shoot me a private message here- let's make it happen
Papa Lazarou
Member
I have no doubt I can help make what you need, but I'm having a hard time trying to picture what you need. Can you (or someone) send me a draft a rough sketch of what you need? Preferably with measurements so I know what dimensions I'm working with.
I'd likely make the part using surgical grade stainless steel (probably wouldn't cost more than $15 for a small adapter), or I could work with one of several different glassblowers depending on the needs.
You can fill out a custom request form on my site, or shoot me a private message here- let's make it happen
Excellent!
I know I have this which does the reverse of what we need.
Battery Free Ganz to DynaVap Adapter
We have had the Battery Free Ganz to DynaVap adapter made to allow people to connect their Dani Fusion (or other BFG) tip to any DynaVap stem of their choosing.
Basically swap the sizes of the female and male joint.
At the moment it accepts a 9mm Fusion head in the top female joint and the bottom male connector is 8mm for connecting to stock dynavap stems etc. We need the opposite - top female joint to be 8mm to accept dynavap/tempest tips etc and the bottom male connector to be 9mm to connect to BFG Fusion stems etc.
I think I’ve explained this right but maybe one of the others can chime in and confirm either way?
GitRekt
Well-Known Member
This is exactly right! We'd need the cutouts for the o-rings just like the adapter that papa linked. Having @Delta3DStudios make this would be huge! You're one of my favorite vendors already!Excellent!
I know I have this which does the reverse of what we need.
Battery Free Ganz to DynaVap Adapter
We have had the Battery Free Ganz to DynaVap adapter made to allow people to connect their Dani Fusion (or other BFG) tip to any DynaVap stem of their choosing.recommendedvapesupplies.co.uk
Basically swap the sizes of the female and male joint.
At the moment it accepts a 9mm Fusion head in the top female joint and the bottom male connector is 8mm for connecting to stock dynavap stems etc. We need the opposite - top female joint to be 8mm to accept dynavap/tempest tips etc and the bottom male connector to be 9mm to connect to BFG Fusion stems etc.
I think I’ve explained this right but maybe one of the others can chime in and confirm either way?
@ScruffyWoofers makes a nice 8mm device to 9mm stem adapter. Bought one a couple months back for a friend who wanted to run his tempest on a 9mm stunner stem. As with everything he makes the quality was top notch
This sounds very doable, but I would need to know what size o-rings you intend to use (thickness + inside diameter) so I can model them in the software).
If I'm gathering this correctly - you need a female which is 8mm Inside Diameter, and then on the bottom you need a 9-mm male joint, with O-ring notches? Dude that would take me seconds to make, complete with a tapered inlet to avoid any hard angles which would be harder to clean.
Cost wise we'd be looking at less than $15+ shipping made with surgical grade stainless steel.
I'm putting together another bulk order of metal prints from my printing partner, turnaround time is about five weeks (or less) so I do it in large batches. If anyone is willing to help with beta-testing, I'll absolutely make this happen. Just shoot me a private message.
Someone please contact me if you have the vape parts and willing to help do testing. I could have the 3D model finalized in minutes once I have the dimensions of the o-rings lol
If I'm gathering this correctly - you need a female which is 8mm Inside Diameter, and then on the bottom you need a 9-mm male joint, with O-ring notches? Dude that would take me seconds to make, complete with a tapered inlet to avoid any hard angles which would be harder to clean.
Cost wise we'd be looking at less than $15+ shipping made with surgical grade stainless steel.
I'm putting together another bulk order of metal prints from my printing partner, turnaround time is about five weeks (or less) so I do it in large batches. If anyone is willing to help with beta-testing, I'll absolutely make this happen. Just shoot me a private message.
Someone please contact me if you have the vape parts and willing to help do testing. I could have the 3D model finalized in minutes once I have the dimensions of the o-rings lol
Last edited:
GitRekt
Well-Known Member
This is perfect! Looks like standard O Rings are 8mm OD 6mm ID 1mm Width. I'd buy two right off the bat, and it sounds like there are a lot of other people who are interested. Once you post this in the Dani thread you'll probably get tons of interest from people with 9mm stems and other devices with 8mm tips.