Search results

A hydratube hydrafoot style stand would take up less table top space

Yes - there's a screen to stop bits being blown back into the heater. And a Stainless Steel disc between the screen and the heater that must be creating negative pressure in the centre as the air enters the bowl.

I've definitely seen an improvement in diffusion and more uniform heat spread by placing a disc in the debrid screen in my DiY efforts since following @Alan 's posting on the subject https://fuckcombustion.com/threads/the-hi.4693/page-249#post-1437961...

I'd have a look back at some of the builds posted in the thread (and the other 510 weed atomizer threads) already and see what takes your fancy. My fav Stempod dual coil builds were with some exotic wires like these Super Clapton wires (and some of the other SS ones in the dropdown)...

Inside the ecig atomizers the wick (and liquid) is in contact with the coil In a weed atomizer there's always a gap between the coil and the load so we need to compensate for that. It's just usually in the region of 50 - 100% extra TCR (the Splinters for example have a SS mesh element but we...

Oh no :) It's a lot easier with an Arctic Fox mod lol Here's how to set the TCR in escribe ... https://forum.evolvapor.com/topic/70149-tcr-value/ Open the materials tab Choose the custom material option so you can give it a name you'll remember Select Actions > temperature coefficient of...

@vapegeezer That's not the easiest question to answer quickly and concisely Here's a good start point https://www.ecigssa.co.za/guide-to-fine-tuning-temp-control-vaping.t18206/ Imagine a box on the graph, that we want to intersect for temp control To do that we can change the angle of the...

Maybe if you put some Titanium (or other metal) balls in the Elev8R ????

Ooooh you may be able to use the smaller 10W Halostar bulb instead as they're actually 11W ;)

Like! :tup: It's a little bigger than I thought it'd be How much power is it using at the moment ?

The Elev8R heater has an 18mm male joint so it will fit on anything with a female 18mm socket (like the bowl) As the hydratube hydrafoot stand has an 18mm male joint you would need an 18mm f/f adapter to go on top (to basically give the stand a sex change) Or if you're going to use a brush...

It was all quite painless, I basically did what they did in the videos Tape up your screwdrivers so you don't scratch the coil Take your time opening the coil, twisting the screwdriver in the same motion every 45 degrees or so around the coil to evenly spread the loops. Try and seat the coil as...

Maybe lol I am using 4mm Rubies in mine but some have said that 4mm are too big to get past all the spikes in their Elev8Rs

Yes - Lots of us have as it was the only option before VGoodiez and Elev8R started selling them as a package Here are a couple of videos done by forum members that you might find useful A couple of people have said that they are running at lower temps with a layer of Aluminium foil...

I would get an Induction Heater for the Vapcap It's unlikely they'll know what the IH is and confiscate it unless they see you using it up close. You could probably pass it off as a power bank for your phone or something if challenged.

I though you were gonna say you pop a denture cleaning tab (or 2) in there and let them soak overnight lol That's what I do with the awkward ones I can't get the bendy brush in, like the sidecar

They don't call them J-hooks on the black leaf website I couldn't find a 14mm male but here's 2 18mm Fs you could use with an adapter https://blackleaf.eu/cane-gun-mouth-piece-clear https://blackleaf.eu/black-leaf-mouth-piece-clear

Just me then? lol I've been having a blast with the 6.5mm heater rod and my lab glass collection :science: The temps came down to 650 and 680 with the two different length 19/26 builds with 2.5 or 3mm balls in the body section with the Elev8R (short) and Herbo (deep) bowls and are quicker to...

I recommend using the tools over at https://www.steam-engine.org/ before you go cutting any mesh or wires

I've built a few DiY G things with those ones, posting the wires in through the side arm ^^^ I think these are the TAG ones http://www.888medicate.com/product/tag-adapter-for-vaporizers-with-10mm-carb/