Search results

I’ve still been using my Flower Mill, but I’m a little concerned about whether or not I should be and whether or not I will need to replace any parts. Being a light user I haven’t seen obvious wear so far, but if aluminum dust is making its way into my flower… It would be nice to get some info...

What does it smell like? Mine smells maybe something like the water from a vase that had flowers in it if I don’t clean it for a while, but nothing that I’d think was worse than smoking… If you’re extracting a lot fast you can certainly get some condensation on your glass or even possibly in...

I hope someone who has a Pinky will respond, but I wanted to ask you first, where did you get the housing and does it flake or smell bad or anything? Someone else in the Pinky thread had similar complaints (an experienced vaporist) and I suspect that part could be a low quality knockoff rather...

Since it says the battery enclosure is reusable, maybe with the right tool anyone will be able to swap them? Less convenient than the bare batteries, but I get why he would go in that direction… I’m a little concerned about the practicality of the oven/capsule too, but I’m guessing he expects...

I feel bad for anyone who has to navigate our health care system…especially without insurance. It’s hard to believe that we let people needlessly suffer like this. :rant: I hope you can get your hand taken care of soon, and I know you must need to work to get the money to fix it, but I hope a...

I haven’t bought anything from them, but there are a fair amount of people here who have. I’ve seen people talk about their products quite a few times and I haven’t seen any mention of shady business practices. I did find a couple of mentions of this age verification system from a few years...

I think there are upsides and downsides to using a wide shallow bowl vs a narrow and deeper bowl, but what’s more important is how well either one gets extracted. I actually like both slower extraction over 5-10+ draws or fast extraction in 1-3 or so, but either way ideally I don’t want it to...

I don’t know which of your ideas is the best/most manufacturable/etc. but eventually I’ve gotta’ get a chance to try at least one of them! :rofl: :popcorn: As for starting a new thread vs staying here though, a clean start with something new might be nice, but everyone watching this thread...

For a mix of logs and ball filled heaters, the CouchLog has been getting some love lately. https://fuckcombustion.com/threads/couchlog.51564/

I think the mods would remove the “Discontinued” tag if you asked, especially if you’re working on a new version. It’s still even in upcoming/unreleased, so no need to rush to discontinued!

In case you didn’t know, the current Omni has a groove you can fit a CCD or screen into in the body in case you want it short too. :) …I haven’t tried it yet, but it should work fine.

:rofl: Yeah, they’re always in the same place within the device, but the electronics are in the middle above the heater if it’s standing upright (stem up), and the battery is on the other side…if you turn the whole device on its side the electronics will be next to the heater and the battery...

When I’m pre-heating it I hold it fairly straight up and down which leaves the electronics above the heater. In use it’s turned up toward horizontal so the heater is below the electronics and/or battery…I only mention it because that seems like the worst case scenario for heat issues and that’s...

If the flower is loose and it gets above the air intake holes that’s not ideal, but otherwise I don’t see why the orientation should matter much? Heat rises, but in non-WPA use the heater is normally below the electronics and/or battery…I can’t see how reversing that would hurt anything. :shrug:

He’s doing his best to catch up, but Nomads take a lot of time… I’ve seen both Nomads and Toads going out the door though, and mine are nearly done, so I feel like maybe it’s a good time to cut him some slack…?

If paypal is cracking down on the sale of these evil devices, I can see why he might be concerned. I don’t remember if he already had problems with them or not, but if he made a bunch of FW8s and had $50,000 in orders come in through them and then they decided to freeze his account or...

I know I always come off as a defender of Dan’s, because I am, but I really do understand the frustration. My Nomad is almost done now, but it’s taken far longer than I ever expected for a variety of reasons. I’m okay with it, but I do want to say that part of the Toad delay (which is also...

invertedisdeadheads? :whoa:

@garm You may be able to clean the wood with acetone, but you’d want to wait a while before using it again. Water or steam would probably do more harm than good. Maybe look at how people clean wooden pipes? I think they just use pipe cleaners to remove large debris? If you combust in the...