Search results

I've used the app, but ive not had any extra charges on my card

Or grinding different strains at the same time:tup:

I don't usually do 2nd squishes, bottle tek or not. I think the highest return I've measured was around 27% with some really nice skywalker

Just ordered a replacement Ti post from Vapefiend and noticed they now accept Bitpay I can see me paying for future orders with Bitcoin now, thanks @VapeFiend.com :) Now if only they'd hurry up and stock the VROD Sic dishes too ;)

I've used 37 micron stainless steel mesh in the past with a small amounts of soft hash http://i.imgur.com/7X5MaWe.jpg Coffee filters work too, but you have to go really slowly and use much lower temps than flower. [edit] this was pressed between some straighteners & a clamp using paper coffee...

Maybe... When I turn off the coil, but leave the controller on, the led is off. I think it sounds like a dodgy pid. But this is the first enail I've owned

When running the calibration, the led flashes rapidly. After calibration, the led will still flash, but slower. To calibrate, I turn on the enail controller, set the temperature, flick the second switch to turn on the coil and hold down the > key until the led starts flashing quickly. I...

Looks like @VapeFiend.com have had another delivery and have glass bowls and the VROD listed. https://vapefiend.co.uk/collections/newvape/products/flowerpot-v-rod-head-diffuser? Unfortunately no SIC dishes (only 25mm and dnail) yet tho.

^Agreed. I didn't buy the flowerpot expecting it to give me a bigger/better/different high. I bought the flowerpot hoping it's usage would mitigate some of the issues I had with the EVO I find the bowls easier to empty/clean than the baskets, the airflow is much less restricted and I can have a...

I got one of these the other day to try with CBD isolate Seems to work quite well for me on an istick Pico or a dna75 at around 25-30 watts. I find I need to preheat for a few seconds before trying to draw and use my finger to feather the carb for best results. Still experimenting. Any tips or...

I have in the past had to complain about a badly formed joint on a drop down. I sent pictures of the joint together, along with the end of a paperclip inserted to show how there was a large enough gap and explained to them that it was not sealing properly.

I'm either over 700 uncapped with a fairly quick draw or around 630 capped for single hitters

The joint seems ok on this piece. It seems to get a good seal with my flowerpot bowls or drop downs. I guess there is a very slight wiggle, but not enough to concern me. I really like the piece so far. It's quite a smooth purr, hardly any change of getting water in my mouth, and little to no...

This little GB-379 bubbler arrived today from Yingmin5 on DHgate: https://imgur.com/a/ac3rBZK I'm quite pleased overall, but the description on DHGate is contradictory. The listing shows 12 inch height and also shows the joint size to be both 19mm and 14mm. The actual height is just under 9...

When running the calibration, the led flashes rapidly. After calibration, the led will still flash, but slower. To calibrate, I turn on the enail controller, set the temperature, flick the second switch to turn on the coil and hold down the > key until the led starts flashing quickly. I...

I still haven't been able to get my showerhead apart either. :shrug: Not too bothered at the moment tho.. Still no vrods at vapefiend anyway

Wow, that SS press looks really good and very compact too for 10 tons

sounds like the heat exchanger would be the 20mm pyrex tube with the enail heater around method reminds me of the vapexhale evo

Thanks :) I only usually use the nugsmasher mini for pressing small amounts (usually sugar trim) and it works well as a personal press, but I've had a couple of occasions where I'd have liked to be able to squish a bit more at once to save presses/time. The only thing that concerns me slightly...

The new press looks really good @dabpress.com :tup: I already have a nugsmasher mini, but I'm quite tempted by this for the slightly larger plates. hmm, PAS? (press acquisition syndrome?) lol