Search results

@Mister G It is a recommendation from the inventor as it results in a lower user temp as the silicone absorbs too much heat. There is a 35 degree difference apparently.

@JCat I forgot that you most likely don't know how I use my 3 and now 4. Initially with the 3 I used the bowl system but as time went on it got frustrating for me. I looked no alternatives and found the Vapocane bowl that allows me to do full convection hits, as the load is outside the vape...

One more extra benefit of the mod we are forgetting to talk about and it's pretty big!! I had to go back a bit and check a post of @JCat to confirm it to myself. The SV3 Mod also has an extra +-50g of aluminum added to the original heat exchanger! No wonder this bad boy does not drop a lot...

Hope these help! View of end of heat tube with silicone cut even This is partially inserted, you can see the gap. When sealed there are no gaps, it's great that the red grommets are so soft! Now it's easy to load and just drop the Sv4 on top and wait +-30 seconds! I would go down to 620F to...

It's your choice bro but i will use the SV4! Even more dangerous!

@Dubmonkey It is very important to remove most of that silicone as I said before. It takes around 40-+ degrees more than if you removed it. Please do this before trying again tonight. @Dubmonkey I went into the vape cave to experiment for you! Since we both do not like the way the SV4 loads...

LOL!! Sorry I am a dental guy and it was an old one from the lab for free! I have 10 inches of space when the screwed all the way up, so it should be good. Thinking of removing the top plate and just using a short length of SS tube to attach to it and then the 3X3 plate will screw onto that...

@Dubmonkey Any news from your testing last night? Hoping it was a good one and it was successful!!

Not even the 3X3 plates? I am only wanting to press small amounts and not all the time. I was hoping to use something like this in the press I have: https://www.newvape.com/errlpress-2-rosin-press-plates Thought the press would be okay for small plates you are selling.

We will have to agree to disagree on this one! LOL! What counts at the end of the day is how it performs for you when you have it all set up and ready to go! I really hope it opens up a lot of new experiences for you!

Totally agree that you need a custom base of known materials. Have you checked out the Musa Vaporizer? Similar to what you are doing but he has a custom control box for dimming and temp control. Adding as much mass as you can will be beneficial in aiding long hits, they mesh is the key! I...

What if the bulbs light had to turn a slight corner and reduce the blinking? Something like the Herbalizer, the bulb blinks but it is not annoying at all. Also it will not be such a large housing as in the video, i would imagine. I know the straight glass tube housing the bulb surrounded by a...

Love all of the halogen vape development going on at the moment!! Nice clean and easy heat source. I dream of a DIY digital halogen vape with a thermocouple to regulate the bulbs output! Looking forward to your developments!!!

A quick test today! That was take two as take one, which was better, turned out to be just a picture... Either way it was two hits and quit, each one was 0,1g.

Moar Mass!!! Keep the dabbing surface but do not mill the slot for extra mass!

I hate doing stuff like this because i feel as if a lot of people don't understand me or my thought process. It was this that started it all: "It actually performs even BETTER due to that TC/coil hack @JCat did! " :D:lol::brow::rofl::love: In my mind, they still work exactly the same, just the...

@Dubmonkey Just had a quick look at my FP SH bowl, you mentioned the carb not sure how that will work. My way would be to use the FP bowl with a basket screen near the bottom of the FP bowl hole. The SV4 will fit into the hole of the FP bowl with a bit of space, you can overcome this by adding...

@dabpress.com When I click your links they go to Amazon.com and it does not ship to Canada. Anyway this could be fixed? One last question! I have one of these presses at home: https://udscanada.com/products/dental-laboratory-hydraulic-press-epi-1 I am wondering if it would be good to use with...

Just make sure the coil has no way of moving away from the heat exchanger, there has to be 100% contact. Also remember that i am not using the bowl system... Set it at 620F and wait for the temp to stabilize, then just figure out how long to leave the stem inserted before hitting for max...

After a few bowls yesterday at 585F, I decided to go up in temp and see what happened. I also brought out a few WT's from storage for testing. Since I was upping the temp, I also moved the small silicone seal all the way to the bottom of the heat tube. Still only using the full convection mod...