Search results

This suggestion might be good for a Yocan Evolve or even my Puffco Plus attys but I would never suggest a box mod lower than 50W output. If you ever want to run a Divine Tribes Ceramic atty or any dry herb kits or any 510nail kits you may want/need more power. I recall the DTV3 required 35ish...

http://fuckcombustion.com/threads/silicone-carbide-titanium-hybrid-nails.16527/page-8#post-1110020 In this thread your answers will be found. If you start at the beginning you will see how I didn't really grasp the concept of the differences. Had I known I would not have spent the $30 on the...

This was extremely helpful. I have been thinking of holding off on the flowerpot because I figured it was a kit deal only or something like that. I can just buy the flower pot body and a 16mm coil and I am in the FP club! @NewVape710 Is the new design of the body that fits the DNail SIC dish...

Sorry for taking so long to respond. I like the Puffco Plus because ease of use and flavor. The dab tool makes it really easy to load even with less stable concentrates. It also pops bubbles as they are created by the heating/boiling of the concentrates. The flavor doesn't typically degrade much...

A lot of people on here are happy running their SIC dishes at 600-610F. I have gone that low with the dnail on my RDK-200 successfully, however I tend to keep it around 625-650 just as a personal preference.

I was looking at that one but it is 2x the cost. I do have a 26 gal compressor that rarely sees use but I don't intend on going pneumatic as it just seems unnecessary and overkill perhaps. Maybe you guys can tell me otherwise I also really do like orange tho! You guys are totally taking...

Can you turn it on with the remote from another room?

I went ahead and purchased the 3x5 caged kit from LowTemp-Plates this morning. Thanks for doing the math for me @invertedisdead I am thinking the 6 ton will not be enough pressure cause like you said I don't want the machine at max capacity. I wanted to be able to conceal the press, however I...

It seems the cages are valued at about $200-$300 for 3x5 or 4x4 setups so an extra $79 for a cage seems like too sweet a deal to pass on after more thought. Plus the plates are both 1" thick in the caged version instead of 1 being 1" and the other being 2" thick. Finally, shipping and taxes are...

The labor time I was talking about is mostly from collecting, not from squishing. It is better for me if I can collect more at one setting as it typically takes me time because I also tend to separate it into single use dabs. I won't trade off on flavor, but I don't agree that a larger plate...

Sometimes I may prefer to press an 1/8 or 1/4 so that is why I want the 3x5 plates. I just see 3x3 being too small IMHO. I will look at the Nugsmasher Mini some more, but I am not too impressed with it honestly. The thing I don't like about the low temp plates is they only use a single...

Hair straightener just wont cut it anymore. I want to squish about 2-3 grams at a time probably as now I usually press .5-1.5 grams. I am only squishing flower currently and doubt I will be pressing anything else as its all too hard to acquire. This is for personal use only but I need to be able...

I believe the less chance of receiving a DOA unit to be very key. Of course there is also the fact that our failed units just improved the wattage output of the device from 50 to 75. Most people want the manufacturer to rush and get this out the door so they can try it. I wanted something that...

I believe the Kiln requires a box mod. If it is the case that a box mod is no problem, then I would suggest the Puffco Plus just because I prefer the easy cup design with the dap tool. I also believe it is the tastiest concentrate pen I have tried that is out there currently but that is really a...

Shoot RBT an email. It sounds like either your heater is shorting on itself or the pot knob is stuck on the lowest setting. I had similar symptoms and initially RBT thought it was a malfunction in the pot knob. After a physical inspection he diagnosed it to be a malfunction in the heater. It...

I will be making a purchase in the next couple days. Don't want to have to jerry-rig my high-temp hair straightener back up and the low-temp straightener only lasted 2 weeks and is now covered in white glue from the back of the plates. I will let everyone know what direction I go in. Also, I am...

I am not too interested in the nugsmasher mini only because I feel I would be limited with that setup. I do like it though. If it was $300, I might have been willing to buy into it. What is the difference between caged and non-caged plates? I am willing to spend a little more on the...

Do you have any updates on the smaller plate kits? I am looking to buy a couple plates with heaters to build my own setup.

I want to get some real rosin plates and build my own DIY rosin setup. I have been using a hair straightener in a bench vice for a year or so now and I am ready for an upgrade. I was considering using the new plates in my vice until I am ready to upgrade to a Harbor Freight hydraulic press or...

Your praise on here as of late has been a reflection of my experience this weekend. My Zion showed up originally with a heater malfunction. I sent it back and all within a week or perhaps less even, I recieved a nice email from Ryan thoroughly explaining the problem, a tracking number and my...