Search results

And testability and apparently repairability. Their design clearly does not provide for accurate and precise fault diagnosis and they can't seem to make subassemblies (e.g. body and back end) with sufficiently close tolerances to support interchangability. Mine worked like a champ for 18...

This is only my opinion and nothing more. But I really do think that the change from OG to Precision HT's was more to do with supply and cost than performance. The choice seems pretty easy these days, though, as VXH doesn't offer the OG HT's anymore. To me, the difference in performance and...

No...the flower does not cook during pre-heat. The oven is not that hot and its full convection so no extraction until you draw. Oh, I supposed if you had a REALLY BIG mod with lots of batteries and just left it in cruise for half an hour that it would dry out your herbs and maybe drive out...

I haven't really found this to be true. With a four minute pre-heat of a .2-ish size load through a nice 65 mm stemless can bubbler, pulling as hard as I can....well, I have gotten as big of clouds out of the G43 as I have gotten from any vape. Two huge draws then a few clean ups. This is not...

So his customers don’t burn their house down and suit him.

There is no problem with the battery sled version's function or performance. But you can't find an 18650 battery sled with built in protection circuits. He's working on an affordable solution.

My solution, in general, is to no longer do pre-orders.

Yes, same with Shower Head....the heater does, after all, need to fit but also be easy to put on and remove so a little bit of space in there is desireable, IMO. I always use the carb cap and I hold the cap down to level the heater.

Hopper Labs doesn't comment anywhere. Hopper Labs does not, IMO, directly engage in conversations with their customers.....they just publish BS month blog emails. I had customers....if we didn't listen and discuss with our customers we would have been very quickly out of busines. These guys...

Yes indeed it is and while I may not use it everyday...I have a number of vapes...it has a cherished spot in my collection and I will never sell it. This is how I use my Enano mostly:

Do we all feel better now? :evil:

Yeah, Stu...absolutely. But I opened the forum yesterday I believe and I would bet that 90% of the first four pages of "new posts" was Chinese spam. I know... you are not the admin....and the admin ...well, let's leave it at that.

Yep...and I'm just sitting here trying to figure out how to tell Markus Storz that I'm his long lost son...DADDY, its me....Baron, your son!! :spliff:

FFS...why can these guys NOT make a consistent product. My OG ran best at 4.2, you could run at 5 to finish up and not combust, and at 2 it would just taste a bit. NOW, after RMA its 5 only if yo want vapor and the AVB is still too green and undone. They SAID that they have new and much...

Lot of people including me and there ain't a dang thing wrong with an Auber...doesn't matter the coil or the banger as long as pin outs are compatible...but I do run my 710coil QB and coil off of a RDK-300.

Hi guys - I have been watching this thread and indeed the grinder looks very nice. As someone mentioned above, non-anodized naked version, as well as the bundle, should be considered for implementation (well, I know the bundle is). I have 4 grinders now (and I have given a few away!!) and...

Yeah, just fine...just a little hysteresis on the temp sensor circuit.

Calming down from what....politics? Sorry, my dear friend...but I'm sick of politics and in DC the merry go round never stops.

I understand. I though we were speculating about the cause of the blue flickering light the poster was seeing in his Volcano. I thought it may be the motor on the air pumping system, be it fan or diaphragm pump. Cheers

Still has annelectricmitir though, right?