Search results

You are only looking to harden it up in the freezer, so 10 minutes or so is usually enough. Unless you heat purge it longer it will not be as stable. So don't expect shatter without heat purging. Once the errl gets back up to around room temp it will be somewhat soft again. It will still...

I would definitely step down the filter size, with 10 micron being the last. Currently I go from a big mesh pasta strainer to a 25 micron then to the 10. I set one on top of the other. The pasta strainer is just to get most of the herb away from the iso as fast as possible, that way I can...

Filters you can get from 316T - http://www.316twholesale.com/ They ship worldwide. You can also get a kit to run BHO. The 7 - 10g kit is $5.99 with screens. You are suppose to grind with BHO (from what I read) so you should be good to go with it. Winterizing is the process of dissolving...

@yaron what kind of filter(s) would you use? If you have a 10 micron SS filter you might be ok. Other than that everything I read says to not break it up much for ISO least you get too much plant material in you final. You could try to winterize after you have your qwiso to remove extra waxes...

I ordered a 710 last night. So looks like I have a month-ish wait? Can. Not. Wait. Will be my first oil rig. Pretty new to the oil game. I have just been dabbing on an rda coil or other vap attys. I have a cheap bong I used for combustion (no more) that I wasn't thinking of converting, but...

For some pics and tips on winterizing check out the instruction manual for the liquidizer. The winterizing section starts on page 18. http://www.liquidizer.com/instructions/

8 to 12g. Avg around 10. As you said, lots of variables there. Highly dependent on the quality of the buds.

I used about 4 grams the first run.

Finished it up today. Around 3ish hours on 110. Let the stuff it my pic above air evap for 2 days. Meant to grab a pic after I got home (before I heated purged) but forgot. Not sure how much it is as the only scale I have is for food and only reads in 1 gram increments. Probably a little...

I have wondered about doing this as well and read it in the Skunk Pharm instructions. I first I read it as "back into container and back in the freezer" but mine was still soaked in iso and I thought that it wouldn't be good (still being stripped). And with the lid on the iso can't escape...

I just do consecutive wet washes. I push/squeeze the herb in the first mesh strainer to try and get as much of the iso out as possible. I'll let that wash make it through the 25 micron screen, then throw the herb from the strainer back into the mason jar, pour the iso in for 15ish seconds, then...

Did my 3rd qwiso run today. I did 2 20 second washes and 1 10 second wash, all into the same pyrex. I haven't used much herb for either of my 3 tries, probably around 4-6 grams each time. Probably closer to 5 this time. Last time I used a nogoo silicone plate, it is was crazy hard to scrap...

I just use another razor to scrap everything to the end. Then I transfer that to a container, parchment paper, slick pad, etc. You'll need to do this a few times on both razors and you should get most of it.

Rebuildable Dripping Atomizer and If I Recall Correctly

I have been running a wick in my dab setup. It is a chimney build though, so the wick is around the outside of the coil. I just drop smallish dabs in the middle of the coil. Not much gets on the deck. Just in case after a few hits I drip some EJ mix in there, hoping that it mixes with any...

The vacuum generator that I linked to attaches to a hose from an air compressor and creates the vacuum using the venturi effect. I'm just wondering if the vacuum generator generates enough of a vacuum, 2.2 CFM at 27" Hg in the case of the one I have. I guess I'll look at the specs of the...

Would vacuum generators that hook up to air compressors work? I have one I used with some composite layup. I since lost my compressor, but would rather spend $400ish on a new compressor (that I can use for a lot of things) than $200ish for a vacuum pump. Here is the one I have -...

Really new to vaping and wax in general. Here is my current setup for wax. It is a temp control ni wire build on a marquis rda. twisted 28/32 ga ni wire tensioned (jig) wrapped 8 times around a m4 screw. It is setup in chimney mode on the marquis. Wicked with KGD cotton. TC set at 420 and...

I'm really digging my lemo drop for ej mix and concretes. I currently have it setup with a ni wire build for temp control. I have 3 2mm readyxwicks stuffed into the coil. Works pretty well at 16-20 watts at 420 degrees. Going to finish what I have in the tank and then rebuild. I'll get...