Search results

  1. OF

    The Arizer Air

    IMO no need to look further, isn't that exactly what you'd expect? Exactly? They're sure not going to want to allow their accessory harmed their product. They're standing behind it in any case. I'm with you, risks without much benefit. Even if the heat isn't bad for the electronics, which...
  2. OF

    Vapman

    I too am interested in how the holes are made. But I'm not sure it's not borosilicate, it most likely is. Due to the fact little guys like this are blown into compound dies and have thread fit and other issues this is the standard material for screw top dram vials, for instance. It's not all...
  3. OF

    Vapman

    Beats me, I buy in person. If I were ordering it for stems I'd suggest they cut it into pieces. IIRC there's an extra charge for long packages. Good folks, I'm sure if you asked them (and told them you needed short pieces in the end) they'd come up with something. They have a shop and full...
  4. OF

    Vapman

    http://www.tapplastics.com/product/plastics/plastic_rods_tubes_shapes/clear_acrylic_tubes/141 You want the 1/4 OD size. Yer welcome. OF
  5. OF

    Arizer Solo

    Worth trying for sure, and using if you like the results. But Solo isn't a convection vape (I know it's popularly held to be), but rather conduction Which is why, for instance, Vortex needs more time. In a convection world that's not the case. Air, being drawn in, just doesn't get heated to...
  6. OF

    Vapman

    Good call on the Silicone IMO. Too bad about the Greece part, although I'm sure you like it and all, but that means postage/hassles getting the tube to you would far exceed it's value. I'm sorry I wasn't clear enough. I buy that tube by the six foot 'stick' and was going to cut you a couple...
  7. OF

    The Arizer Air

    I'm with you there, given all the joy the Air delivers it seems so little to ask in return....... OF
  8. OF

    Vapman

    That's not the boiling point, it's the melting point. Vapor (or 'fumes' if you will) can happen below that (many plastics 'smell', so vapor of some sort comes off at room temperature, more when heated). Significantly to this application is the 'softening point', when it starts to get soft and...
  9. OF

    Arizer Solo

    PBW, hands down: http://fuckcombustion.com/threads/pbw-the-chemistry-of-clean.7854/ Cheaper, safer, easier and more complete cleaning than ISO....... OF
  10. OF

    Arizer Solo

    Check EBay a bit, the fellow also sells larger and smaller lots. For instance: http://www.ebay.com/itm/2-Tobacco-Pipe-Screen-Steel-Gauzes-Conical-Round-Bowl-Cone-6mmx12mm-1-4-x1-2-/201089803281?pt=LH_DefaultDomain_0&hash=item2ed1e2e411 Agreed. They spread through my Solo and Air stems like...
  11. OF

    The Arizer Air

    Yes it does, my mistake, thanks for catching it. The normal sleeve does cover the vents, I had forgotten I'd cut mine off to 'improve' the grip without blocking them on the sleeve I grabbed (I've got a couple, randomly I got the short one....). Since then I cut the top section down a bit to...
  12. OF

    The Arizer Air

    I disagree, I see no advantage WRT longer component life, we should not to block the vents. Blocking the vents raises the temperatures in the oven and cover, while included in the design, raising the temperature of oven parts even more won't help them last longer. That design would have...
  13. OF

    The Arizer Air

    Trying to clean every bit of the 'dark stains' is likely to be near impossible. It's almost certainly fine Carbon deposits (what you get from Hydrocarbons after you 'burn of the Hydro parts'....), the very sort of stuff that 'seasons' a cast iron skillet. Like in the Iron pan it's filling in...
  14. OF

    Discontinued Elevape SV

    Exactly so. IMO that's got to be it. The black part (anodizing?) has to be worn off for 'the silver ring' to show. They all seem to start out black and run to silver (raw Aluminum). Eventually it stabilizes (stops wearing) when the clearances open up enough. OF
  15. OF

    Ascent Vaporizer by DaVinci

    I don't think so. First off no real sticking issue. I put a toothpick in the outside end hole and pushed it gently both ways. IIRC pushing in was what cracked the thing loose. IMO it's the ring, not the fit, that glues it in place. It may well be different for others, which is why it'd be...
  16. OF

    Arizer Solo

    Cost of ownership is, of course different math. Insurance costs, depreciation and so on. You might even make money tax wise? 15 broken stems? Mighty impressive! Good show you and Ataxian are about 8 time zones apart...... Me too, and a tried a lot of times, really. A few high probability...
  17. OF

    Ascent Vaporizer by DaVinci

    I realize it's borderline 'cruel and unusual' to discuss the spacers when they are not yet available to most owners and all, but that's not my intent. I'm confident they will soon be common fare (included with new units instead of the jars?). Once any issues that might come along have been...
  18. OF

    Arizer Solo

    I don't doubt that a bit. You can easily have spent a bundle if you wanted to. But that's an individual call. And it's an option. Sort of like adding the cost of the Canadian vacation you intend to take to the cost of the new car? Also, as I see it, when you buy all that lovely aftermarket...
  19. OF

    Arizer Solo

    I understand that amongst the S&B guys that's known as 'a glass free air path'....... OF
  20. OF

    Arizer Solo

    Shhh! Let's keep that to ourselves, right? We need these young sprouts to stay in the salt mines if we want this retirement thing to work out...... OF
View older results
Top Bottom