Search results

  1. OF

    Arizer Solo

    But conduction and convection don't really happen together like that I think. The hottest part of the system is the metal cup. Any conected air, heated by that cup, can't be any hotter. Nor can the stem wall or any part of the load. The best it can be is as hot as the cup. 'Real' convection...
  2. OF

    The Arizer Air

    Careful there, wishful thinking often leads to dreams. And dreams are what get us outside the box as a society, clearly worth considerable risk. And for sure wishful thinking and vision are what drives those dream born ideas into being...... New stuff in the marketplace? Yeah!!! Wishful...
  3. OF

    Arizer Solo

    Yes, it's a 12 Volt, one Amp (max) source as well. Great for charging, but not for 'charge while using'? Charge while using works OK for things like cell phones that recharge faster than they discharge. Think about it, there's a clue there. Since it takes longer to charge Solo than to...
  4. OF

    The Arizer Air

    Are you sure? The one I measured early on was closer to 5 Amps, which 'fits' with 2.5 Amps for Solo (which has twice the voltage so needs half the current for the same power). Did you actually measure 3 Amps? Likewise, 1C rate is the one hour number. A 2500mAh cell, like we're likely to be...
  5. OF

    Arizer Solo

    I know it would not. The new model cannot run true PA no matter what you plug it into and the PA voltage is too low to even charge the battery. It's useless. Despite what the left over printing on the bottom says. Save your money.......it could come in handy for a new battery when the time...
  6. OF

    The Arizer Air

    I could be, but that depends hugely on you. What you need by was of dose, how much you put in in terms of potency and how skillfully you extract it (mostly not taking more than needed I think. As a group this varies a LOT. We have a guy that uses a gram a month......yes, one gram, 30 days...
  7. OF

    The Arizer Air

    We're not going to ask you what you've been holding in your other hand all that time........it's just not that kind of Forum you see...... Glad you found happiness at any rate. OF
  8. OF

    Arizer Solo

    While the exact height is going to vary with stem, draw, strain, cure, phase of the moon and who knows what for sure there's a 'sweet spot' in there to work with. A handy way to do this is to tilt the stem. Raising one side up 2mm is the same as lifting the stem evenly one. This 'fine tune on...
  9. OF

    Arizer Solo

    No, it's not. Backing the stem out cuts the heating by conduction. Heat movement into the load is decreased and heat loss from the load increased. OF
  10. OF

    The Arizer Air

    No, not even if they were real......which they are not. It's a fraud. Think about it for a bit, if that (no doubt 'oddball') maker really had invented a battery twice as powerful as all it's competitors wouldn't they own the world right now? Like sell the 18650s used in every Tesla electric...
  11. OF

    Arizer Solo

    No, not significantly. It does draw a small fraction of the power from the battery but otherwise is a true bypass. All of the 2.5 Amps or so for the heater comes from the PA. Notice it's 9 Volts not 12? That's how the originals knew to charge or run PA. FWIW I like the old version for this...
  12. OF

    Arizer Solo

    Like many rumors, based in fact I think. Two issues come to mind right off. First the wall wart isn't big enough to run the heater alone, let alone charge the battery. It's good for a bit less than half the total power needed when the heater is heating (LED flashing), the other half (actually...
  13. OF

    Divine Tribe atty's

    We're saying the same thing I think. I want to shorten the cylindrical part under the taper by maybe half? You could also cut the height of the belled out bottom (that fits over the lower body against the o-rings. You could easily cut 1/4 inch looks like, maybe even 3/8. Fine tuning yet to...
  14. OF

    The Arizer Air

    Hard to argue with a customer like that. Nor figure what to do next...... Cheaper is always nice, I guess? OF
  15. OF

    Discontinued Elevape SV

    Stranger than you can imagine I bet........ Good luck in the holy quest. OF
  16. OF

    Divine Tribe atty's

    No, but they can be enough alike so they can perform 'right' in the overall system. That is the mod can adjust for differences. In fact, it's adjusting to changes (differences.....) when in TCR mode? Rant on that very topic coming up in fact: Makes perfect sense to me. Do you really...
  17. OF

    Discontinued Elevape SV

    Yeah, sounds worth returning to me. I run XP (Pro) to mine, it works. IIRC it called for some fiddling as often happens. I got lost on the "really wanted a go of the vape" above. Seems important (reaching goals......), what was it you were looking for in a vape? OF
  18. OF

    Discontinued Elevape SV

    So you haven't tried connecting by the app and USB? I'd definitely do that. Your call, of course. Did the seller advise you it was broken? What does he have to say? OF
  19. OF

    Discontinued Elevape SV

    You bought it from the maker on EBay? IMO it's very unlikely DOA in that case, it's tested and configured too much in manufacture for that. What happens when you connect via the app? What level of battery charge does it show? Any chance it's already fully charged? OF
  20. OF

    The Arizer Air

    Lots of us have/do. Be sure to use real milk, not nonfat, reduced fat, 2% or any of that. It's the milk fat that does the work...... A shot a cream of 'half and half' is good insurance for full extraction. You'll probably want at least a couple dozen mg of THC, meaning .1 gram is a good...
Top Bottom