Search results

I do a 1/2 gram of 20% flower daily. My concentrates vary from 60% for live rosin to 85% resins. By my calculations, that a $6-8/day medication. That more than doubles my annual cost for medicine. Of course, that assumes efficiency of delivery. As long as the packaging doesn't say if its...

Now that's a plan :clap: I can see that as the best of both worlds.

There's 12 18650 cells in the battery so it a reasonable to believe their capacity. I have 3500mah cells capable of 10 amps continuous.

You can run a Cauldron on a battery powered source. I run my ZVS IH using 3s 18650 with perfect results and that is only 11.1v when the peek wears off. Not having a battery in the Cauldron is an advantage. You could even make a variable voltage power bank... here Just put the converter on a...

Maybe Stupid should be a different race.

Agreed. There is very little difference at that point. The bag will be slightly more homogenized temperatures due to settling time. Vape bubbles in water will be warm in the center and cooler/condensing at the air bubble boundary. The coolest vape will remain in the bubbler of course.

Interesting. So figuring out how to equal my current dose would be some effort. Concentrate here is around 20/g on average. But I don't know that it is activated (decarboxilated). I always thought the vaping process was the activation process.

Doctors practice medicine - Politicians practice politicking. Neither knows exactly what they're doing.

I am still torn between these two units. I ran the 2s wand for a couple of days and enjoyed it immensely. Thick heavy rips and very fast vanquishing of the load. Then a couple of days with the AC brick dialing the power levels and going back to native 3-4 draws on a very hot setting...

$60 on a new M isn't bad. $90 for a new one and a proper '19-M for a friend and a '20-M makes it $45 each. Either way, you'll get more than that back in appreciation. I got it because there isn't anything else to buy and do want to try the half-bowl setting.

As far as materials go, stainless steel is safe at vaping temps. Copper has never bothered me at reasonable temperatures under 150F. An organized thread? Is that even possible?

The problem I had with stainless steel was contact resistance. The contact points got very hot until I went with copper. After that, they remained warm to the touch but not hot. This has a lot to do with thermal conductivity. Considering the temperature elevation of the puck in the LB, this...

Didn't think of that.

I actually experience the very same symptoms with edibles because they are mostly lesser quality flower. That is why I know it isn't just the act of vaping causing symptoms. This is a chemical sensitivity. That is why I am shopping farms so rigorously. Oregon Roots has become a trusted...

Okay, didn't need it but got one anyway... '20-M on the way. 4:19 came and went in trying to find the C-Vap. One needs to log in to see the offer it turns out. Order placed by 2:36PM Left Coast Time.

I don't see a way to order the C-vap ... - gotta have an account to see it. Okay, '20-M on the way. Can't buy just the tip yet.

@Polarbearboy - What exactly is vaping doing? Is it bronchial or the actual air sacks and lung mass? My issues are broncial based on some fertilizers or pesticides. Our state is pretty good about testing for illegal stuff and exceeding limits but I am sensitive to some that are used on lower...

Right - charring or burning is decomposition. So you need the temperature at which charring commences. https://www.newark.com/pdfs/techarticles/alphaWire/HeatShrinkTubing.pdf The lowest shrink temperature in this offering is 90C. This is way below decomposition temperature as you don't want...

https://www.panduit.com/content/dam/panduit/en/support/material-safety-data-sheets/heat-shrinkable-tubing-whmis-0.pdf Typical shrink tubing MSDS You'd need to bring the material to a decomposition state normally associated with combustion to have any harmful effects from this. Being a cold...

Way cool of you George! Thanks :rockon: