Search results

Just in case you don't know already you can put a dynavap fat mouthpiece in the TM tube. You can also cut the tip of that silicone mouthpiece just to get the taper part (pictured with @dzoinp mods in the link below) https://fuckcombustion.com/threads/tinymight-tm-2.44563/post-1598437

Mouth to lung hits with airflow closed/almost closed. You can take a few inhales in a raw before the exhale. The bowl is the part that needs to cool before reusing (the part with the clicker), not the whole oven (the part you screw the bowl in). The bowl takes around 10 seconds on a magnet to...

Box mod Lost Vape Paranormal DNA 250C in good condition, with a few scratches on the edges (see picture). I have to check but I may still have the printer and splinter Z profiles on my computer if interested. I can send more pictures if needed. Price is 75€ + shipping

A bit off topic but I have to say that isn't my experience at all. Before the TM2, I brought my TM everywhere with me (hike, concerts etc.) without any protection, directly in my backpack or jacket/jeans pocket. It's not that fragile at all. I also don't find it fiddly at all. You can straw suck...

The Anvil is specifically designed for this purpose and does its job really well IMO. I think TM/TM2 is very close if not on par with the Anvil for this but is more versatile.

Yes, IMHO the "bypass" setting should bypass the helix/cooling unit, as it is the case with the DRC tube. Otherwise, what does the air bypasses ? 😅

I think there is an error between the illustrations corresponding to "open" and "bypass" with the direct airflow tube ? (@Brenyo)

Thank you guys ! So it's sure I did read it and forgot... :doh: sorry Sure ! Thanks for the excuse 😅 On my TM the TM2 battery cap just makes contact with the battery after half a turn and i can go a bit more than a 1/4 turn more without much force then it's locked. Same feeling than with the...

Could you maybe give me a link to that post please? I read this thread everyday and didn't read that post

Yeah I saw that post too. Thought at the time that if it can turn on i see no reason it couldn't vape but I'm no electrical engineer so today I decided to try it. IMO the risk of frying my unit was low and i learned so much from the community here that taking the small risk was kind of a "thank...

I just tried taking a hit with the batterie cover of the TM2 on my TM OG and it worked as usual :2c:

Yes you can. I did. You can even add a bit of baking soda 👍

Yes rizzla is a brand of rolling papers and i also think the metal tanks are both parts of the CU. It seems to act as an o-ring in the middle cooling unit but it's not made of silicone, that he wants to avoid iirc. Ok, understood. If you're using the original assembly of the cooling unit I...

Even though English isn't my native language, I'm not bad a it and i can't figure out at all what you're describing neither. And I read it a few times. :2c:

Could you post a picture of it ? When you say the contacts a loose, are not attached at all to the motor ? Does that motor still look like this ? If so, you may just have to gently bend those legs a little upward so they make better contact to the electronic board.

On the TM the vibration motor was attached to the bottom aluminum plate and was held in a soft silicone housing, with two little legs that make contact to the electronic board once the plate is screwed to the body, and sometimes could get dislodged and thus not functioning properly. If it's...

I think you just need to recalibrate your TM2

Not practical but the solution to clear your hit in session mode would be to take out the stem from the unit before the end of your daw

I have a Xtar ST2 that is capable of charging 2 18650 at 4.1A with the right socket plug. I always had good results using S&B capsules with my TM. Even though I pushed the heater screen 2-3 times not being careful, it luckily didn't damaged my unit. I only use capsules when I want to be 100%...