Search results

Scroll to the bottom of the page for a nice bowl 14 or 18. http://www.vriptech.com/mm5/merchant.mvc?Screen=SFNT David

Thank you One too many zeros in each. I use about half the normal amount. Just to increase airflow I was quite a few bowls in last night.

Some Injector and bowl combinations leave the coil and heat source far from the load.. Look at a pic of the injector in an Eds Bowl. Last night I took the 18mm post from my ShovelHead bowl and tried it in all my bowls. It went to the bottom of my 18mm cheap bowl and fit fine on another...

What is the actual capacity of the bowl ? Size? David

Give it a shot. Some one want to count frames? David Simple, if you want to know if the injector fits a bowl, just use your 19mm post for the shovel head. OR most anyh 19mm thinghy. https://cdn.discordapp.com/attachments/855507713996095521/933171700605026364/20220118_190938.mp4 Will do...

I see your point. I have an Xmax V3 and it is convection. Capsule is hot when I take it out. So hot I cant pick it up and flip it over. I have also taken a crafty capsuld and put it in an Ispire banger. It fits well and seals at the bottom. It worked using my New Vape WeedEater head...

I would love to see it on my door step in USA! DAVID

I have walked into smoke shops with the entire coil in hand. "What is that?" Then I tell them I want a bowl that is 22 mm OD. They say We only have 14 and 18mm. I took the nub. The guy put out a rack of bowls. 18 AND 14. It fit most all. The only problem some are not round and the nub...

Rustyoldnail, Put .15 in the pod it will probably work better. Hot spots in the center are a sign over packed environment. I use them in the Crafty and with my flower pot. Any time I drop them out of the crafty, they are HOT. I looked at buying a HERBIE. It was WAY above my pay...

It fits some from what I have read right here. You asked for pics. Originally it was the bottom nut of a WeedEater. I cut it up saving the holes and threads. This was the beginning B1 bottom, WeedEater top nut, full of balls, WeedEater bottom nut screwed it on WeedEater top nut...

Results from the last photo. AVB A pic of the part only in a few.

Latest Report of the nub on my B1. Works EXCELLENT! Better than the shovel head. I think the heat is closer to the herb. All Glass must help. No doubt it hits quicker than the shovel head. Its all we have been using. Shovel head is sitting on a shelf. My nub with the B1 is the best...

Creaking on warm up and cool down is normal. I spread my coil. No big deal. Just look at an elev8tor heater. Tried to see t h e live stream. Phone was terrible. Sound was intermittent or none . David

I posted pictures on Discord under new products. No attachments right now on this site. Really works like I expected. HARD hits. Milks up FAST. A definite improvement. David

It would be best to try to get it apart when its HOT. David

Finished today. I shortened the post on top. Now it sticks up .4" from the top of the nut. Fits 18 to 14 adapter quite well. Fits in the Shovel head. fits in most glass bowls. I do put the bowl on the head, block the bottom with my hand and suck to see if I get a seal. Some glass is...

After some scientific testing, the W2? Beadeater? Weedballer? Speedballer? Speedballer II. (2 sides) This thing is the BALLS! Photos tomorrow. Works in lots, even most glass bowls. Top or bottom, same temp setting so far. David

Ok, I did it, chopped up the WeedEater and made a glass bowl adapter. It's not an injector, just a male part that fits in most glass bowls. Looks good, cannot try it right now, but later with a report. I am trying for pictures. David

YES

For the screen in the bottom of a glass bowl, I form the screen in a dome with the edges lifted from the bottom. Right now I am using one of the bowls that come with the Ispire Wand and I have one other glass, but it has a single hole with no screen. It works OK, but draw is limited...