Search results

It's pretty bad. There is still 100,000 homes without power across the GTA area. And a really cold snap has moved in. Here' my back porch. Ugly and beautiful at the same time. My brother in law had a huge salt water aquarium with a living reef. All dead. Brrrr. Glad you joined the lucky ones...

Just got power back. Luckier than many.

Hi @Caligula, hope all is well. The stand can be made with either plug size. As an AIO owner, your price is $15 + 15 shipping for the non-lite. Just fill in the order request and we'll get you set up.

Hi guys, been busy working on a new design for the Solo stand and think most will like the changes. First thing is the accuracy of the stand as a whole is much more precise. The big ass hole is now gone and the air flow for the bottom holes in the Solo is now routed along a cut in the inside of...

I would be suspicious and send it back. It sounds like the temperature sensor has a bad connection. This would cause the heat to run a muck. In my thinking anyway. Screwing the top or changing the pressure may have been enough to cause the connection to work again. Try loosening it to see if...

Being the owner of both PNWT and the F-Bomb, I had wrote a comparison review in the PNWT vs F-Bomb thread when I first got the PNWT. I have been using both for a while now and as I had stated in my review the PNWT wins on almost all fronts but two which seems to be the complaints in the last...

I don't think that the 9 volt tester you have will give a valid reading on "defective" batteries. You see the testing is looking for voltage "without" load. Many battery failures will measure good until you load them down and then the voltage drops. Causing the Solo to go wacky. Not saying the...

Yeah, you'll never hear him say size isn't important. :suspicious:

This is a hard one to find. I looked for many hours. If you do find, let me know. That's how I use it all the time. Less worry about breakage. Have a custom stem from Ed coming soon to take it's place. A shorter Ed's Zebrawood stem with the end shaped more for the Gong. Yeah....

For you guys that need a stand for your 14mm stuff. Here is a makeshift ghetto stand. Have been going to post for a while but had to wait until I caught one which was used up. I tend to get into trouble trashing stuff around here....:rolleyes: Just cut off the thinner tip and the rest is the...

Sweet, a cascaded heating system. Sounds awesome in deed. Having (making) the right jigs to make stuff is half the fun. Your quite welcome and will keep an eye out for your results. :tup:

Cool, that would at give a 2 for one if not three. Even more if you can find the wire on spools. Just remember the voltage provides the heat and the capacitance determines the length of time it is heating. So what you look for is how much discolouration there is around the weld caused by the...

I'm not sure about making thermocouples as I was looking for a way to attached the kanthal element wire to non-resistive wire. RBA = ReBuildable Atomizer. There are some out there that require the wires to be attached in this way. Or twisting together. It should be considered a battery tab...

Hey guys. A while back I got myself a new RBA and it is the type that you need to attach pieces of non resistive wire to the ends of the kanthal wire. I have been doing the twisting together method which works but seems to loosen up over a short time. Read up on how ecig guys made the weld...

Would work. However, if soft type silicone similar to the HT tubing, it would also become sticky over time. The tube I use to hold the 14mm Gong connector to my bowl goes sticky and I replace every month or two. OTOH, if harder type silicone, would likely be fine but you loss the elasticity...

Please see PM. EDIT. I feel it necessary to give an update here and give an advisory. There seems to be some misconception on the usage of the Solo in PA mode. The battery DOES need some charge to use in PA. Reports of "unit not heating in PA mode" has been reported a few times now and solution...

Here's a glass shop I came across which has lots of glass that seems a good match for the Solo. Even has a 18mm WT that looks like it has a smaller mouth piece. Has your name on it @ataxian. I was trying to order just the 90 degree 14mm elbow to use with the Gong when using dry. An alternative...

LOL, the boot is a stem holder to give a place to sit it between loading. The lean and boot toe is so it can hold bent stems as well. Just a small stem stand to keep your stem safe. Your very welcome, Pipes

I've been thinking about the changes and thought I'd add my 2 cents. IMO, Arizer has made the changes based on product history and to increase future sales. (marketing) I'll bet they have had these updates on their mind for a long time (maybe from the start?) but wanted to establish a very...

That is a very common cord type. The same as desktop PCs as well as many different devices requiring a 3 prog cord. Check out that old stuff in storage that never gets thrown out. Good chance you'll find one.