Search results

It is now ceramic for less metal in the vapor path as many people want. Are you hearing the loud 'click' when you insert the oven into the body of the vape? It takes a fair amount of pressure to get the oven to seat properly when new. That is a shame, he makes nice stuff but easy enough to...

A Dynavap with an induction heater is my go-to when I want that joint-like experience, a close second for me is a XVAPE WPA (the glass is about the diameter of a 2 paper) on a Roffu using a stainless steel oven with dosing caps, I can blow vapor rings with mouth pulls once things heat up. I use...

As explained, these go on the filter in the heating chamber, shown here, I still run my OG without any seal in the bottom of the heater post of the main unit, my chambers seal quite well without it and newer versions only have a snap ring securing the heater chamber, no seals.:tup:

Great advice above, also, if your troubles started after cleaning/disassembly, ensure the grommet (called a filter on page 3 of the Roffu manual, the silicon part above the spiral is the part I usually insert the wrong way around but that just restricts airflow) above the oven is installed with...

https://vimeo.com/802930491?share=copy edit to say you could take your grinder to a skateboard shop and get them to swap it as this bearing size suits most skateboards...model #608 or S608, actual size is 8x22x7mm

I had a mix of boro balls and rubies (4 and 5mm) In my old D020-d

As @billyfitz said above, the Avant now has USB-C for charging. We have also updated a few other aspects of the vape including the colours available to spice things up, The improvements are only slight but they add up to deliver quite a good little conduction vape at a great price point. I have...

I have dropped a few terp pearls in the diffuser of the odd water pipe just for fun and that does increase resistance that can be adjusted by adding/subtracting balls.

Eco mode on my friends Venty almost from new (I had to set it up for him)...it was later replaced due to E04 and he will not firmware update the new one as per Aussie seller instructions (the seller said 10% of his replacement units would E04 after firmware updating). He has not had a problem...

That fix was canned, it was too hard for many people to swap (me included, I use my OG with no o-ring) so in the end any peeps that presented with that problem (to me at least) simply had their units replaced.

I was thinking your replacement may not have been that old, worth a try if you explained it is the old problem rearing its head (the auto ghost sesh/puff) and you only just noticed it happening.

My OG still acts this way and as you said, these were replaced where necessary under warranty (not all had this glitch). Sorry to hear you have an ongoing problem with the Roffu, please start another RMA as this problem has been fixed (auto firing)...you must have just been unlucky with your...

I have asked for another update on listing the cooling unit body separately, hope to hear something soon. My OG Roffu is now just over 2 years old and the puff counter has just reached 10,000.:cool: I did find out the puff counter does not advance by simply turning it on as my counter was on...

I can relate, I have an oz of Incredible Bulk sealed in a small mason jar with a Boost and had another with Boveda that is over 2 years old...I think I must have already vaped the one with Boveda so I have nothing to compare the Boost stored oz against. At least it is the same strain that I...

It sounds like your main unit may be the problem. Keep talking to JCVAP to get sorted, you seem to be one of the very few people who has had problems so you might have just been the unlucky person to get a dud (of which there seem to be few).

I only use them for burping and fresh ground buds that are being used... long-term, vac seal, o2 scrubbers and Boveda for insurance in wide mouth mason jars.:tup:

My 22ltr CVault saves a lot of time when curing, I got sick of burping 'many' quart wide mouth jars and I like to hand stir the contents when burping. I save the vac seal for when the burpin is done. I have also had success with my new Twist mini CVaults for storing ground herb ready for...

I suspend a small glass beaker that has iso and the atty in the ultrasonic cleaner tub that holds 2ltr of water. The ultrasonic waves are not slowed down by the glass. Here is how but with old Mighty caps in the iso, Plastic test tubes are also great to fill with iso and suspend in the water...

I have 3xOG that all still work fine and never had a problem but I rarely pull the atomizer apart, I just ultrasonic clean the whole atty in 100% iso like a Puffco Peak Pro...on a regular basis.

I call that a micro dose.:2c: A Plenty bowl can hold at least 10x that, here is a spent Plenty puck, The Plenty is hard to beat for getting baked simply due to the huge bowl...but alas, it is not portable.