Woah! Okay big brain. I’ll try it out.
This is cool af.
-
SCAM WARNING! See how this scam works in Classifieds.
This is cool af.
budski
cantre member
I find the v2 to be closer to cxl than to the v1; which is kinda what they were shooting for I think. The smaller form factor of the v2 may be better for some, but I found on after market stems it hangs with the cxls in rotation. and is unnecessary if you already have a cxl
I hope they order more v1 caps because I love to use those on the dynas.
Thanks!I find the v2 to be closer to cxl than to the v1; which is kinda what they were shooting for I think. The smaller form factor of the v2 may be better for some, but I found on after market stems it hangs with the cxls in rotation. and is unnecessary if you already have a cxl
I hope they order more v1 caps because I love to use those on the dynas.
I have the V2 and am considering getting the CXL. Do the caps hold well on the Dynas?
BallzMcVinegar
Well-Known Member
I was able to get a few extra V1 caps for that same reason. I will say the V2 does deliver and Ive been reaching for that often. I do think it is an upgrade but I still have a soft spot for the V1.I find the v2 to be closer to cxl than to the v1; which is kinda what they were shooting for I think. The smaller form factor of the v2 may be better for some, but I found on after market stems it hangs with the cxls in rotation. and is unnecessary if you already have a cxl
I hope they order more v1 caps because I love to use those on the dynas.
Thanks for this idea. My Omni is colleting dust, because it's my least favorite one, while the V1 together with my Fusion is the preferred solution. I'll give it a shot.
SlickHenry
Well-Known Member
I have used the V2 a few times with the wand. My wand has the larger opening on the underside so I tend to use that end with all my TEDs as it's what I am used to. I usually insert it on auto mode so the cap notches are level with the red ring. I leave it in there for 8-10 blinks for first heat up, approximately 5 on reheats (depending on battery level and if inside/outside). I just tend to insert it level so it's an even distance from the edges. I have tried rotating but it makes no discernible difference to me so I generally don't bother. You get a surprising amount of vapor for a bowl and I find I am heating it 4-6 times to finish a bowl. It has replaced the Dynavap M as my everyday pocketable vape probably cos the heat up/cool down is faster and the bowl size is larger.
Last edited:
Hello everyone,
I just received the V2, and I can confirm that it doesn't work with YLL 2.0.
So, I'm considering buying a Wand. Do you have any recommendations for a silicone adapter: Dynavap, Tempest Quartz Adapter for Wand?
For use with the V1, V2, and also the XL.
Thanks for your replies.
I just received the V2, and I can confirm that it doesn't work with YLL 2.0.
So, I'm considering buying a Wand. Do you have any recommendations for a silicone adapter: Dynavap, Tempest Quartz Adapter for Wand?
For use with the V1, V2, and also the XL.
Thanks for your replies.
I don't use any adapter. I use the V1, V2 and XL. With the V1 and XL I active heat with the wand, with the V2 I preheat only.
Recently the V2 in a dry pipe config has been the daily driver. But I've been loading it differently.
Finer grind, straw load with a decent tamp. Can really get the bowl to roll with thick vapor if you pack it just a bit.
I have timings down but with the wand the plates start to vibrate with the radio frequencies and heat when it's at the right temp.
I usually go past this sound for a second or two, and pay EXTRA attention to it with fresh batteries.
The V2 head with the increased iron really makes heating so fast with the wand. And it's lovely that it isn't big enough to move like the XL cap
Timings on previous page, or treat the vibrating discs as "the click"
snowboardbum
New Member
V2 arrived in the mail today. What's the best way to clean it for first time use?
budski
cantre member
I do this too