-
SCAM WARNING! See how this scam works in Classifieds.
The Tempest by Mad Heaters & Phatpiggie
- Thread starter oddjobold
- Start date
cuckF0mbustion
New Member
I have read a few times now that the titanium heat shield doesn't have any practical effect outside of adding weight and cost to the tempest. I bought one anyway because I just like nice machining and can appreciate it even more with something like titanium. I just had one question about it though. Is it actually true that there's literally no benefit to it? I saw Brenyo say in a response on here that the titanium sleeve will basically never get hot. Would that be slightly different compared to the aluminum heat shield? I'm wondering if the full titanium version maybe does actually have one advantage, albeit a small one, in that it may be better for back to back to back bowls and heavy use? I'm not sure if this is an accurate way to think about it or not though
GuiAlGhaib
New Member
Hi everyone, I'm a proud owner of the Tempest V1 and it's been my daily driver for the past few months. I'm really enjoying the experience.
My wife currently uses a DaVinci IQ2, but with the V2 pre-order now open, we're planning to switch her over to a Tempest as well. She occasionally uses my V1, but misses the longer sessions that electronic vapes can offer.
Since the Tempest is so customizable, I think we can tweak it to get closer to that kind of experience. In that context, what kind of balls would you recommend to extend the session feel? I was thinking the new ruby balls might help, but I’m not entirely sure.
Any suggestions?
My wife currently uses a DaVinci IQ2, but with the V2 pre-order now open, we're planning to switch her over to a Tempest as well. She occasionally uses my V1, but misses the longer sessions that electronic vapes can offer.
Since the Tempest is so customizable, I think we can tweak it to get closer to that kind of experience. In that context, what kind of balls would you recommend to extend the session feel? I was thinking the new ruby balls might help, but I’m not entirely sure.
Any suggestions?
BushRanger
Hit It & Quit It
Happy 420! 
Watch Tempest on Stationary Donut with Forge | Streamable
Watch "Tempest on Stationary Donut with Forge" on Streamable.
streamable.com
Minsc_NBoo
Active Member
Happy 420 everybody 
Its 9:30pm UK time, and I'm just about to have my first session of the night.
Its 9:30pm UK time, and I'm just about to have my first session of the night.
zatonic
Well-Known Member
Check out the tempest manual page on their website for ball options. They break it down with material density and recommended temps. Looks like stainless balls may be the best option
.d
Wubba Lubba dub-dub
Everytime I see this black beauty my eyes tear up 🥹Happy 420 everybody
Its 9:30pm UK time, and I'm just about to have my first session of the night.
One day…
cuckF0mbustion
New Member
I think you're probably right. I do know though that often with titanium parts, manufacturers just don't want to make them because it's so much harder to machine than aluminum. I'm not sure if there's something about the geometry of the heat shield that makes it particularly difficult to make out of titanium and just looking at the images of it, I can't imagine anything but it's possible though. I don't know anything about his supply side but it's possible that the titanium shield is added on at cost or very near it because it's already so much more and if that's the case then I would understand not wanting to offer it even if it did stay cooler. This is a lot of "ifs" though. I'm not expecting a practical difference either. Really I'm just excited and can't stop thinking about it lol
zatonic
Well-Known Member
Yeah I think you're on to something.
- Aluminum is way easier to machine than titanium. It cuts faster, produces less tool wear, and is generally more forgiving.
- This means shorter cycle times, less expensive tooling, and fewer issues during production—which can improve overall productivity and reduce downtime.
Fearless Disaster
Well-Known Member
Hi tempest friends! So for 420 I had the opportunity to go to a social event and vape out a bunch of friends. This is a rarer but important use case for me, so much so that I would keep a dedicated device ready for it. I chose to take my tempest with my wood and glass aezhenn stem instead of my TM2 because I didn't want to have to give anyone instructions beyond "don't touch the metal part, its hot". It was cool because my buddy is a mighty user and the house owner was a dab straw user so I got to show them some cutting edge dhv tech. I felt like a dhv ambassador 
I have usually just packed tempest 1/4 to 1/2 loads for myself and have just done single heatups. At the party I packed around 4 bowls mostly back to back. Since I can't see the VI when the tempest is in the wand, I ended up using the wand more like a torch. I would drop the tempest in for a few seconds, then pull and check the VI and adjust as necessary. I tried to bring the VI up to the second indicator. Once I thought the vapor was a little thin so i pushed it to the third indicator and combusted.
There were a lot of variables.. sometimes there were enough folks around to just pack back to back, sometimes folks were good so i would hang onto a half toasted bowl for a bit and then try to reheat it for the next person. at times when it had cooled down more i wanted to reheat it a little more but after combusting i just kept it to the second indicator and figured that a little underextraction was better that combusting again.
How do you all handle this use case? I had never needed to reheat a single bowl or pack back to back before this. I am hoping that just reheating to the second indicator should be enough, and maybe if its still thin just heat again to the second indicator after a hit or two. What do you think?
Also, does anyone know of leatherworkers that can make a case for the wand? Duba doesn't have a wand to design around. i realize that for this use case i don't even need the mh wand stand thing. i end up just holding the wand in my hand constantly and dropping the tempest in for a few seconds at a time. I thought that if would be awesome to have a tighter fitting leather case for the wand that would provide some protection from button presses and moving the wand adapter within the head. If the wand can be run inside the case great, if not maybe the part that covers the head could flip back like a hood and play the part of the mh wand stand.
I have usually just packed tempest 1/4 to 1/2 loads for myself and have just done single heatups. At the party I packed around 4 bowls mostly back to back. Since I can't see the VI when the tempest is in the wand, I ended up using the wand more like a torch. I would drop the tempest in for a few seconds, then pull and check the VI and adjust as necessary. I tried to bring the VI up to the second indicator. Once I thought the vapor was a little thin so i pushed it to the third indicator and combusted.
There were a lot of variables.. sometimes there were enough folks around to just pack back to back, sometimes folks were good so i would hang onto a half toasted bowl for a bit and then try to reheat it for the next person. at times when it had cooled down more i wanted to reheat it a little more but after combusting i just kept it to the second indicator and figured that a little underextraction was better that combusting again.
How do you all handle this use case? I had never needed to reheat a single bowl or pack back to back before this. I am hoping that just reheating to the second indicator should be enough, and maybe if its still thin just heat again to the second indicator after a hit or two. What do you think?
Also, does anyone know of leatherworkers that can make a case for the wand? Duba doesn't have a wand to design around. i realize that for this use case i don't even need the mh wand stand thing. i end up just holding the wand in my hand constantly and dropping the tempest in for a few seconds at a time. I thought that if would be awesome to have a tighter fitting leather case for the wand that would provide some protection from button presses and moving the wand adapter within the head. If the wand can be run inside the case great, if not maybe the part that covers the head could flip back like a hood and play the part of the mh wand stand.
cuckF0mbustion
New Member
Hi tempest friends! So for 420 I had the opportunity to go to a social event and vape out a bunch of friends. This is a rarer but important use case for me, so much so that I would keep a dedicated device ready for it. I chose to take my tempest with my wood and glass aezhenn stem instead of my TM2 because I didn't want to have to give anyone instructions beyond "don't touch the metal part, its hot". It was cool because my buddy is a mighty user and the house owner was a dab straw user so I got to show them some cutting edge dhv tech. I felt like a dhv ambassador
I have usually just packed tempest 1/4 to 1/2 loads for myself and have just done single heatups. At the party I packed around 4 bowls mostly back to back. Since I can't see the VI when the tempest is in the wand, I ended up using the wand more like a torch. I would drop the tempest in for a few seconds, then pull and check the VI and adjust as necessary. I tried to bring the VI up to the second indicator. Once I thought the vapor was a little thin so i pushed it to the third indicator and combusted.
There were a lot of variables.. sometimes there were enough folks around to just pack back to back, sometimes folks were good so i would hang onto a half toasted bowl for a bit and then try to reheat it for the next person. at times when it had cooled down more i wanted to reheat it a little more but after combusting i just kept it to the second indicator and figured that a little underextraction was better that combusting again.
How do you all handle this use case? I had never needed to reheat a single bowl or pack back to back before this. I am hoping that just reheating to the second indicator should be enough, and maybe if its still thin just heat again to the second indicator after a hit or two. What do you think?
Also, does anyone know of leatherworkers that can make a case for the wand? Duba doesn't have a wand to design around. i realize that for this use case i don't even need the mh wand stand thing. i end up just holding the wand in my hand constantly and dropping the tempest in for a few seconds at a time. I thought that if would be awesome to have a tighter fitting leather case for the wand that would provide some protection from button presses and moving the wand adapter within the head. If the wand can be run inside the case great, if not maybe the part that covers the head could flip back like a hood and play the part of the mh wand stand.
If you plan on not finishing the bowl then you would want to try to concentrate your heat towards the very tip so you get the balls hotter than the rest. I have no experience with the wand but just for example if you were using the torch, you'd focus the flame at the very tip of the device instead of somewhere down further on the cap. You'll always get some amount of conduction but from my (admittedly limited) experience with the tempest, it's better than most portable dry herb vapes for this. Basically you want to bias your heating strategy as far towards convection and as far away from conduction as possible
TigoleBitties
Big and Bouncy
I'm a Wand user too but I have a Stunner instead of a Tempest. I think they should behave similarly though. The Stunner has no clickers or indicators of any kind so for re-heats what I like to do is to heat with the Wand while also drawing on it simultaneously (hold it up to your face as if lighting a cigar). If you do this and test the vapor density every 5sec or so you should know when it's good to go. No VI needed.Hi tempest friends! So for 420 I had the opportunity to go to a social event and vape out a bunch of friends. This is a rarer but important use case for me, so much so that I would keep a dedicated device ready for it. I chose to take my tempest with my wood and glass aezhenn stem instead of my TM2 because I didn't want to have to give anyone instructions beyond "don't touch the metal part, its hot". It was cool because my buddy is a mighty user and the house owner was a dab straw user so I got to show them some cutting edge dhv tech. I felt like a dhv ambassador
I have usually just packed tempest 1/4 to 1/2 loads for myself and have just done single heatups. At the party I packed around 4 bowls mostly back to back. Since I can't see the VI when the tempest is in the wand, I ended up using the wand more like a torch. I would drop the tempest in for a few seconds, then pull and check the VI and adjust as necessary. I tried to bring the VI up to the second indicator. Once I thought the vapor was a little thin so i pushed it to the third indicator and combusted.
There were a lot of variables.. sometimes there were enough folks around to just pack back to back, sometimes folks were good so i would hang onto a half toasted bowl for a bit and then try to reheat it for the next person. at times when it had cooled down more i wanted to reheat it a little more but after combusting i just kept it to the second indicator and figured that a little underextraction was better that combusting again.
How do you all handle this use case? I had never needed to reheat a single bowl or pack back to back before this. I am hoping that just reheating to the second indicator should be enough, and maybe if its still thin just heat again to the second indicator after a hit or two. What do you think?
Also, does anyone know of leatherworkers that can make a case for the wand? Duba doesn't have a wand to design around. i realize that for this use case i don't even need the mh wand stand thing. i end up just holding the wand in my hand constantly and dropping the tempest in for a few seconds at a time. I thought that if would be awesome to have a tighter fitting leather case for the wand that would provide some protection from button presses and moving the wand adapter within the head. If the wand can be run inside the case great, if not maybe the part that covers the head could flip back like a hood and play the part of the mh wand stand.
The nice thing about having a design with an air gap between the bowl and the heater is that you can just wait for things to cool down if you ever overheat the tip. The key to not combusting is to take very light, gentle sips when re-heating. Stop immediately if you taste any scorching.