Smknbud
Well-Known Member
I obviously looked in the wrong area at Delta3DStudios for this SonG for the MV. They still do make it I see. I stand corrected from my earlier comment saying they didn’t make it any more. Had one, gave it to a FC member.
MiniVAP Vaporizer
- Thread starter stinkmeaner
- Start date
Razhumikin
Well-Known Member
I cant find this adapter, if you found the link can you please share?
Knightsofcamelot
Well-Known Member
I sent an email to Delta3dstudios aboutbpicking one up and he sent me this:
Hello!
Thanks for your interest in my small studio. Due to low sales I had actually discontinued those products however I've just enabled them again if you'd like to order one. Although note since they will need to be freshly made there will be a week or so turnaround and they'll likely have a bit of a vinegar odor when received (this is normal, they will air out on their own naturally over a few days).
Cheers!
- Mike
MiniVAP 18mm WaterPipe Adapter
3D Design and Fabrication Studio offering 3D Printed Widgets
delta3dstudios.com
MonkeyTime
Well-Known Member
That's sort of a loaded question. Batteries discharge and degrade over time, short and long!
With a new battery pack and fully charged, the first bowl is about the same, plugged in may heat up just a bit faster. After a bowl or two, wall connection is a better experience.
Please don't take that to mean the batteries aren't good, they are! I don't count how may loads I can run, it's plenty and I have two battery packs if the occasion requires. Again, two because I bought two full sets, not because it was needed. I use it this way more often for the portability.
At my desk, plugged in for the win! Same some battery life and cruise away.
I wonder if there's anyone in the states who has an extra glass adapter that doesn't want it
Otherwise its slow overseas shipping for me
Depends on how you want to connect, or what you're connecting to. There are a lot of ways with the flexicone + !
For HT's which I use often, it's the delta studios song, but I whip connect a lot of glass!
stickstones
Vapor concierge
I love it when this thread picks up! The MV community is one of the most mature vaporist groups around.
Gonna plant my new glass/teflon core on the desk today and see how we do.
Gonna plant my new glass/teflon core on the desk today and see how we do.
Razhumikin
Well-Known Member
Let us know how it goes!
Sn4Pz
Well-Known Member
Im talking about their glass joint, which I plan to use with flexicone+. Originally I wasn't going to go with it because I heard it was equally as unstable as the SonG adapter (which I already have and dont really like the fit of it), but Pagan has said otherwise, and I trust his word
@JCat didnt I see on Reddit that you recently bought one of these? Does that mean we can get minivap stands and trays from you? I would love something to slot my minivap into, with a little built-in stand to slot my hubble bubble onto
Last edited:
Smknbud
Well-Known Member
I got my last MV, QC Teflon, back when you were the rep for those of us in the States and we ordered thru you. Still going strong but I have renewed interest in getting one of the latest convection versions with glass tube. Will try to hold out till 4/20 sale. A glowing review by you may throw that to the wind. Looking forward to what you have to say about it.
Last edited:
Razhumikin
Well-Known Member
Just got my gold minivap and this first bowl has left me deeply, deeply in love. The vapor is unreal.
Knightsofcamelot
Well-Known Member
Noice! Did you get the teflon or glass?
Razhumikin
Well-Known Member
Acutally I seem to be having an issue. The first bowl worked great, but now when i try to use it it cycles through the colors when i turn it on, but then immediately the color indicator turns red and the device stops being responsive. I cant change the temp or even turn it off after that. It seems to be happening with both the battery and the power adapter. Has this happened to anyone else?
teflon! hopefully i can work out this kink and go back to enjoying it asap.
Razhumikin
Well-Known Member
I believe so, the battery indicator shows its at full battery and it clicked in.
Actually I think im just a stoned idiot and it wasnt totally tightened.
kimura
Well-Known Member
Been there
Razhumikin
Well-Known Member
Im blown away by how efficient and flavorful this thing is. It tastes like a perfectly executed firefly hit EVERY TIME. Insane.
Pagan Zod
Well-Known Member
I have that issue too. Not sure what is causing it to lock up because my battery is always tight (I make sure to give it a compulsory twist before hitting the buttons, because I still have the habit of holding the device where it twists the battery a little when I pop the cap off), but if you unclick the battery & then click it back in, it will fire right up and off to the races you go.
Sn4Pz
Well-Known Member
I had this happen to me for the first time today as well, I think its a software glitch as opposed to a physical alignment issue because it happened to me while using the AC adapter, and worked perfectly again after I just unplugged and replugged it.
Weird
Razhumikin
Well-Known Member
Similar to Pagan Zod, I find that if I untwist and then re-snap it in it resolves the issue. My guess of why this is happening is that the contact points between the oven and the battery/adapter may not be perfectly aligned, even when it seems like its locked into place and things should be set. Im not sure how a software glitch would cause this, but then again I know literally nothing about how it works internally.I had this happen to me for the first time today as well, I think its a software glitch as opposed to a physical alignment issue because it happened to me while using the AC adapter, and worked perfectly again after I just unplugged and replugged it.
Weird
MinnBobber
Well-Known Member
Electrical contact point alignment:
Note that the contact points are VERY tiny so the margin for error is small.
Misalignment can cause a partial connection and problems. Usually this is from not twisting together far enough. However, I have one unit where you can twist too far and the contacts only partially touch.
If you get blinky lights, always disconnect and reconnect the battery or AC puck.
Note that the contact points are VERY tiny so the margin for error is small.
Misalignment can cause a partial connection and problems. Usually this is from not twisting together far enough. However, I have one unit where you can twist too far and the contacts only partially touch.
If you get blinky lights, always disconnect and reconnect the battery or AC puck.
MonkeyTime
Well-Known Member
Those with connection issues using a battery, the other thing to check, but I believe my situation was a one-off, is the tightness of the battery housing.
One of my battery packs came back or was purchased and needed the screws tightened before it would make contact consistently. It was easy to notice the difference between two packs, but not sure how fast I would have caught it otherwise. I believe it was three allen head screws in the bottom, no issues since snugging them up.
One of my battery packs came back or was purchased and needed the screws tightened before it would make contact consistently. It was easy to notice the difference between two packs, but not sure how fast I would have caught it otherwise. I believe it was three allen head screws in the bottom, no issues since snugging them up.
Razhumikin
Well-Known Member
Is there an agreed-upon ideal grind size for using with the flexicone basket system?
Sn4Pz
Well-Known Member
Im finding it's less about grind and more about properly filling. The small basket isn't large enough for me, and the large basket knocks me on my ass... so I tried to only fill it half way and it was a very underwhelming experience cloud-wise. When I pack it full(/so the herb cant vortex / fly around) its a great time
Fortunately I've found that G43 slide screens fit perfectly, and hold ~1.3-1.4x of what the small basket can hold. Its a perfect size imo.
MinnBobber
Well-Known Member
I find the ideal grind size to be: don’t grind at all. Pluck off individual calyxes and temp step one and two. Open the basket and squeeze with tweezers, they are brittle and pop, big cloud coming your way on the next hits.
I am a flavor chaser so this is probably not how most use theirs.
When I was a grinder, it seemed very flexible, able to handle coarse to fine.