The "Stunner"

tinctorus

tinctorus

Well-Known Member
Accessory Maker
Hey guys I just wanted to finally make a post introduction of my brand new vaporizer I've named "The Stunner"
The stunner is a butane powered ball vape that will fit any 9mm stem, the device uses an easily purchased titanium pill bottle for a top cop, this was done specifically to allow people to cheaply try out tops with different fill materials
I put approximately 50-55 3mm ZrO2 Zirconia balls held in place with a domed basket screen

The bowl/stem section had been machined from 316ss,I have enlarged the bowl to hold a nice big .2 G load, I CHOSE SS specifically for heat retention in the bowl, I've extende the 9mm post in order to prevent any type of sagging of the ball head due to the extra weight out front, I made the diameter of the post just slightly smaller than the Dani v3 in order to prevent any eating of o rings

Units are going to be priced at about $90 plus the shipping for the unit itself without a stem, you will be able to buy them from wesley pipes in the states, soothing vapours in the great north and @tukatukera in the EU, I will start shipping then to the distributors this week

instagram.com

Vapor solutions (@grizzard.mike) | Instagram

979 Followers, 7,722 Following, 112 Posts - See Instagram photos and videos from Vapor solutions (@grizzard.mike)
instagram.com instagram.com
https://imgur.com/a/vVTO9bz

https://imgur.com/a/p94mTYQ

https://imgur.com/a/SA3z32s

 
Last edited:
Oden

Oden

Well-Known Member
tinctorus said:
Hey guys I just wanted to finally make a post introduction of my brand new vaporizer I've named "The Stunner"
The stunner is a butane powered ball vape that will fit any 9mm stem, the device uses an easily purchased titanium pill bottle for a top cop, this was done specifically to allow people to cheaply try out tops with different fill materials
I put approximately 50-55 3mm ZrO2 Zirconia balls held in place with a domed basket screen

The bowl/stem section had been machined from 316ss,I have enlarged the bowl to hold a nice big .2 G load, I CHOSE SS specifically for heat retention in the bowl, I've extende the 9mm post in order to prevent any type of sagging of the ball head due to the extra weight out front, I made the diameter of the post just slightly smaller than the Dani v3 in order to prevent any eating of o rings

Units are going to be priced at about $90 plus the shipping for the unit itself without a stem, you will be able to buy them from wesley pipes in the states, soothing vapours in the great north and @tukatukera in the EU, I will start shipping then to the distributors this week

instagram.com

Vapor solutions (@grizzard.mike) | Instagram

979 Followers, 7,722 Following, 112 Posts - See Instagram photos and videos from Vapor solutions (@grizzard.mike)
instagram.com instagram.com
https://imgur.com/a/vVTO9bz

https://imgur.com/a/p94mTYQ

https://imgur.com/a/SA3z32s

Click to expand...

WOW I love it!
I was considering buying a stealth vaporizer for the outdoors.
And I prefer to support an active member of the community like you.
I guess I have to DM tukatukera to buy it in Europe?

Congratulations on completing your project.
Hoping for great success for you.
 
GoldenBud

GoldenBud

Well-Known Member
It's something that we all seen before.. except the balls man... great job.. maybe the idea is not super "original" but the world doesn't only need people to think about ideas, people will also have to create them... and selling them etc'... the video quality is bad but it looks like people will buy it.... good job, i liked it except the video quality!

in my opinion people will buy it
i think if these balls are expensive, make an option to use Ruby balls too, if it doesn't matter give people the option to buy the least expensive option IMHO. good luck

P.S
maybe even sell the device without beads if it's possible, many people got already Ruby beads that they can use
 
Last edited:
tinctorus

tinctorus

Well-Known Member
Accessory Maker
GoldenBud said:
It's something that we all seen before.. except the balls man... great job.. maybe the idea is not super "original" but the world doesn't only need people to think about ideas, people will also have to create them... and selling them etc'... the video quality is bad but it looks like people will buy it.... good job, i liked it except the video quality!

in my opinion people will buy it
i think if these balls are expensive, make an option to use Ruby balls too, if it doesn't matter give people the option to buy the least expensive option IMHO. good luck

P.S
maybe even sell the device without beads if it's possible, many people got already Ruby beads that they can use
Click to expand...
I think it's only been done as far as a butane ball vape but this is definitely is own little beast IMO, plus it's always good to have options 😂

9mm is definitely the way to go for the airflow as well

😂Yeah I'm NOT any good at all with taking pictures and video, call it a problem for a 40 year old who doesn't grow up with call phones 😂😂

I just got a new phone though and I've been trying to get better with pics and vids
 
P

Pre-stoned

New Member
Oh look at that lovely looking beasty
So this is 9mm compared to the Ta
Does this mean it's compatible with the danni stems.
Loving the fact that it has zirc balls in they truly are best at optimal performance over the bog standard Ruby's most people have.
Is that a glass wood and carbon fibre stem options I see wow that's awsome so modular.
Did I hear right that your also getting a titanium stem maker on board
 
N

norwayp

Member
I have been looking for a dyna style torch vape. This looks like a good fit!

Will it be possible to get in a finished kit for people that doesnt have dyna stuff or similar from before?

Good luck on your launch, looking forward to get my hands on it myself.
 
Last edited:
tinctorus

tinctorus

Well-Known Member
Accessory Maker
Pre-stoned said:
Oh look at that lovely looking beasty
So this is 9mm compared to the Ta
Does this mean it's compatible with the danni stems.
Loving the fact that it has zirc balls in they truly are best at optimal performance over the bog standard Ruby's most people have.
Is that a glass wood and carbon fibre stem options I see wow that's awsome so modular.
Did I hear right that your also getting a titanium stem maker on board
Click to expand...
Lots of info here, yes I've been working with a number of stem makers to bring more 9mm options to market, it'll fit the existing Dani vape stems if you have one already

@leanpubpackage I'm aware of the other unit but the similarities in the overall unit are just that, I've been really open about the fact that this fita a titanium pill top in order to give people cheap options for extra tops with different fill materials, the bowl size, material, full material, unit size is all different and improved

@norwayp absolutely you can get a setup with a stem if you would like
 
Grover

Grover

Well-Known Member
Retailer
Just saying hello and congratulations for bringing your dream to life. We are honoured to be associated with this product and look forward to making Tthe Stunner available to the Canadian cannabis community. We will likely make them available with ruby balls for those who choose this option...I'm sitting on 5000 x 3mm rubies atm so we're good to go!
 
tinctorus

tinctorus

Well-Known Member
Accessory Maker
Grover said:
Just saying hello and congratulations for bringing your dream to life. We are honoured to be associated with this product and look forward to making Tthe Stunner available to the Canadian cannabis community. We will likely make them available with ruby balls for those who choose this option...I'm sitting on 5000 x 3mm rubies atm so we're good to go!
Click to expand...
I'm thrilled really about the whole thing, one of the best parts for me though had been getting to know and work with other people like you and the rest of my distributors, love being able to bring something affordable to market
 
tinctorus

tinctorus

Well-Known Member
Accessory Maker
Sour Dream said:
Super dope can’t wait to get one of these and a TA
Click to expand...
I've been working with a number of stem makers to bring more 9mm options, tiny stems is doing wood ones, Ptglass rockets fit this native but we've also been talking about him building some heady stems, I've also been talking to a titanium stem maker to bring lots of affordable options for people
 
letter never sent

letter never sent

reckoner
tinctorus said:
No there's way more than that buddy

Ok so I've increased the bowl to hold .2 G, I've extended the post to stop sagging of the head, I've decreased the post diameter to stop oring destruction, bowls made from 316ss to retain heat, 9mm post, Zirconia balls
@Noah0608 here you go
Click to expand...

These are all pretty minor differences though. There's no denying this device looks extremely similar to a TA and probably performs very similarly as well.

Obviously you're more than "aware" of the TA - your device would not exist without it.

The fact that you're releasing this just ahead of the expected TA restock kinda rubs me the wrong way tbh. But whatever I guess. This happens constantly in the space now. :shrug:
 
tinctorus

tinctorus

Well-Known Member
Accessory Maker
letter never sent said:
These are all pretty minor differences though. There's no denying this device looks extremely similar to a TA and probably performs very similarly as well.

Obviously you're more than "aware" of the TA - your device would not exist without it.

The fact that you're releasing this just ahead of the expected TA restock kinda rubs me the wrong way tbh. But whatever I guess. This happens constantly in the space now. :shrug:
Click to expand...
Anyone else's release has nothing to do with me tbh, do you also think the coil driven units are the same?
I also don't see how a totally redesigned unit is "minor differences"

And like I've said I specifically chose to use that top to give people options
 
letter never sent

letter never sent

reckoner
tinctorus said:
Anyone else's release has nothing to do with me tbh, do you also think the coil driven units are the same?
I also don't see how a totally redesigned unit is "minor differences"

And like I've said I specifically chose to use that top to give people options
Click to expand...

Totally redesigned? Keep telling yourself that.

Ah yes, the pill bottle idea. Did you get that one from this guy? https://www.reddit.com/r/vaporents/comments/103bmw0
 
TigoleBitties

TigoleBitties

Big and Bouncy
Grover said:
Just saying hello and congratulations for bringing your dream to life. We are honoured to be associated with this product and look forward to making Tthe Stunner available to the Canadian cannabis community. We will likely make them available with ruby balls for those who choose this option...I'm sitting on 5000 x 3mm rubies atm so we're good to go!
Click to expand...
Does this mean no zirconia balls available at the moment? Love your store btw. When do you expect to stock it?
 
You must log in or register to reply here.
Top Bottom