Discontinued The RBT Milaana (unregulated single 18650)

[AJS]

I have read in the thread that you can place your screen at a certain point in the stem and it stays cleaner for a longer time.
Where is this magical, mythical point?
My screen is filthy after each bowl and i place it level with the lip of the stem.

Help??

Well, Idk about this magical screen distance, but what I can tell you is, my screens are almost always spotless. Only need to clean it when the stem is dirty...because I clean it in the stem itself.

Anyway, mine is basket style and pushed down so a tiny bit of glass is showing above the basket, probably 2mm-3mm, as someone else mentioned. I always make sure to blow out my abv after a hit when everything is hot, like after a few hits. And make sure to really blow through the stem.

 

[Shit Snacks]

I have read in the thread that you can place your screen at a certain point in the stem and it stays cleaner for a longer time.
Where is this magical, mythical point?
My screen is filthy after each bowl and i place it level with the lip of the stem.

Help??

What @AJS said, also grind (/herb) consistency is a big factor really, stirring could be too

 

[WakeAndVape]

Blowing outwards when the load is spent and still warm is the best way to keep the screen clean as long as possible as @AJS said.

 

[TeeJay1952]

has anyone set screen to the Enano pick level? 1 1/2 inch

 

[pandaphysics]

Blowing outwards when the load is spent and still warm is the bast way to keep the screen clean as long as possible as @AJS said.

I like to hit it empty and then blow out

 

[flotntoke]

has anyone set screen to the Enano pick level? 1 1/2 inch

nano e-pik notch is actually a little less than 1/2" I think (12 mm?). This is about where I am for a deep big load with Mi. It's 2 - 3 times the usual distance of bare glass to basket screen edge as a regular load for me. Not that they don't hit similarly - they surely do! - but Mi load is way further from heat and much more turbulence/spreading of heat before it gets to load. With nano I try to keep heater core end 2mm or less from load and it's in a tight little tube. Mi is usually loosely packed to edge. Still kind of amazed how close the vapor can be with such different set ups - but both pure convection, so I guess it makes sense. Once you get good convection it just becomes a matter of power/heat level?

I like to hit it empty and then blow out

This works well when you get plenty of heat. I usually wait until battery is about ready to be charged and just hold button longer. So my screens only get heat cleaned every batt - instead of every load - but feel like I'm using most batt power for hitting. They're usually in ISO after 3 to 4 battery changes anyway. Clean screens = GOOD screens!! Same as for any vape.

 

[DDave]

Five more kits listed.

http://www.ebay.com/itm/-/122059018320?

Awaiting stock replenishment now. Will list more as soon as possible...

Edit: Due to International interest, am making arrangements on cheaper shipping. USPS stated shipping to most all international locations would run between $15 & $20USD (a good deal better than the almost $35 currently). Once I am restocked, I should also have the needed shipping supplies to make this happen. Stay tuned!

 

[RastaBuddhaTao]

Milaana said knock you out

 

[murf2010]

Five more kits listed.

http://www.ebay.com/itm/-/122059018320?

Awaiting stock replenishment now. Will list more as soon as possible...

Edit: Due to International interest, am making arrangements on cheaper shipping. USPS stated shipping to most all international locations would run between $15 & $20USD (a good deal better than the almost $35 currently). Once I am restocked, I should also have the needed shipping supplies to make this happen. Stay tuned!

Mine comes tomorrow!! Thanks neighbor!

 

[TeeJay1952]

@RastaBuddhaTao I think here is where your life is somewhat changed. All us folks can post videos under Fair Use but if you do it , the post is a unofficial commercial indorsement and you are liable for damages. I base this on the fact that I have watched LA Law, Boston Legal and Perry Mason so I am well versed. Please send a used Zion for Legal Advice. (Now I violated a law!)

 

[justvapin]

Five more kits listed.

http://www.ebay.com/itm/-/122059018320?

Awaiting stock replenishment now. Will list more as soon as possible...

Edit: Due to International interest, am making arrangements on cheaper shipping. USPS stated shipping to most all international locations would run between $15 & $20USD (a good deal better than the almost $35 currently). Once I am restocked, I should also have the needed shipping supplies to make this happen. Stay tuned!

I got one ordered this time around----Thanks!!

 

[murf2010]

Blowing outwards when the load is spent and still warm is the bast way to keep the screen clean as long as possible as @AJS said.

Think so too. Other wise I gotta clean them really frequently!

 

[DDave]

Is a Dodge Challenger a slightly better version of the chariot?

Unless it happens to be this model Challenger....

Spoiler: Oh yeah!

Mine comes tomorrow!! Thanks neighbor!

Anytime! Enjoy!

@RastaBuddhaTao I think here is where your life is somewhat changed. All us folks can post videos under Fair Use but if you do it , the post is a unofficial commercial indorsement and you are liable for damages. I base this on the fact that I have watched LA Law, Boston Legal and Perry Mason so I am well versed. Please send a used Zion for Legal Advice. (Now I violated a law!)

^^^ This was great.... "However..."

I watch Scorpion.... so if mentioned Zion unit were shipped to me, I would incorporate it into a technological solution that could possibly end world hunger and at the same time play the best of the Jimmy Kimmel show without commercials... Oh, and it would do so while recirculating the residual heat energy through a micro-flux capacitor thereby allowing me to vape a bowl.... travel quickly back in time to just before I vaped the bowl and vape it again.... rinse & repeat!

 

[little maggie]

Five more kits listed.

http://www.ebay.com/itm/-/122059018320?

Awaiting stock replenishment now. Will list more as soon as possible...

Edit: Due to International interest, am making arrangements on cheaper shipping. USPS stated shipping to most all international locations would run between $15 & $20USD (a good deal better than the almost $35 currently). Once I am restocked, I should also have the needed shipping supplies to make this happen. Stay tuned!

Finally! My dog is not home to interfere. I knew it was her fault I was missing these.

 

[WakeAndVape]

Missed the fucking kits again! Had an hour long commute home...should have looked at the thread while I was driving!

Now I'll have to wait for more stock....fml.

Oh well...big loads aboard.

@DDave is eBay the only place to get them or can you just PayPal invoice me when you get more in stock...I don't have my own eBay account, which may add another layer to the order frenzy.

@pandaphysics I don't really like to hit any vape empty... I'm not sure why...'tis what it 'tis

 

[DDave]

@DDave is eBay the only place to get them or can you just PayPal invoice me when you get more in stock...I don't have my own eBay account, which may add another layer to the order frenzy

@WakeAndVape
No prob. . Can send a PayPal invoice.

Circle back with me in a week and I should have an idea when I can start shipping again.

 

[xer0]

@WakeAndVape
No prob. . Can send a PayPal invoice.

Circle back with me in a week and I should have an idea when I can start shipping again.

Any chance you'll sell 18/18 or 14/14 adapters that will work with this kit? I love the idea of basket screens but I primarily use Milaana with a water pipe.

 

[Bravesst]

I have read in the thread that you can place your screen at a certain point in the stem and it stays cleaner for a longer time.
Where is this magical, mythical point?
My screen is filthy after each bowl and i place it level with the lip of the stem.

Help??

This is a low maintenance vape, self-cleaning.
Stems are pretty easy to keep up with as well.

10 TIPS TO A CLEAN STEM
1. Screen closer to tip helps burn off buid up
2. Pull thru an empty stem (heat screen), blow out
3. Do #2 after each stem
4. Occasionally soak stem in some ISO (remove screen)
5. As in 4 above, torch screen back to brand new
6. Try not to leave spent load in stem
7. Small loads, less buid up
8. Always remove stem after each session
9. Stir at least once, manual clean out with stir tool
10. Dry and shred. Wet herb fouls up everything. I use a light bulb and medtainer.

 

[RastaBuddhaTao]

Thanks to all who believe

Please use the code thanksfc for a 10% discount... Only a few days left.

 

[WakeAndVape]

Thanks to all who believe

Please use the code thanksfc for a 10% discount... Only a few days left.

I watched that and it actually inspired some positive energy for the day...good shit.

I thought your face was going to pop up I'm the mix somewhere?

Well there's always the updated version.

Also feel free to carve the new logo on milaana while you have her

I hope the success of this vape will make you feel just as proud and appreciated like the coaching moments with the kids

 

[pandaphysics]

I missed the kit as well. Hopefully I can catch it next time. luckily I've mostly been using my milaana with cotton and wax only last couple days. so effective.

 

[DDave]

Any chance you'll sell 18/18 or 14/14 adapters that will work with this kit? I love the idea of basket screens but I primarily use Milaana with a water pipe.

Yes, most likely in configs of 18/18 & 14/18. Once available, will update thread with news/availability.

I missed the kit as well. Hopefully I can catch it next time. luckily I've mostly been using my milaana with cotton and wax only last couple days. so effective.

Replenishment in progress.... I should have kits available in just over a week.

 

[pandaphysics]

Great! Thanks ddave, ill definitely be looking for the WPA too!

 

[Shit Snacks]

This is a low maintenance vape, self-cleaning.
Stems are pretty easy to keep up with as well.

10 TIPS TO A CLEAN STEM
1. Screen closer to tip helps burn off buid up
2. Pull thru an empty stem (heat screen), blow out
3. Do #2 after each stem
4. Occasionally soak stem in some ISO (remove screen)
5. As in 4 above, torch screen back to brand new
6. Try not to leave spent load in stem
7. Small loads, less buid up
8. Always remove stem after each session
9. Stir at least once, manual clean out with stir tool
10. Dry and shred. Wet herb fouls up everything. I use a light bulb and medtainer.

I would add grind again, true wet herb would be dirtier than dry herb as well... Also I don't torch screens, just iso soak and rinse those as well, I have these steel brushes from Indica that work great to clean out any left specs under water.

With enough screens you can change then a few times before the stem needs to be cleaned even, or with basket style screen placement you can use an iso damp qtip to swab it clean and blow out of both ends to get rid of the dirtiness and moisture, if you don't have enough spare screens and are in between deep cleans

 

[murf2010]

Anyone whose messed with the Zion prefer it over the Mi?? I'm debating on getting a Z

My Mi is like the best thing that's ever happened to me