next generation e-nails?
- Thread starter bassplayer
- Start date
Dramma Lamma
Looks like a job for!
I
Never bought ne thing off mass drop yet not sure.
No clue, but I have no interest in the ti nails so that's got my vote.
Never bought ne thing off mass drop yet not sure.
Herr_Dampf
Well-Known Member
Any special reason to go with a 20mm coil instad of a 15.8? Just wondering because I am about to order and googling the topic just got me more confused
Edit: Joint size ... I maybe should've spent a few more minutes actually reading the Info
Last edited:
syrupy
Authorized Buyer
Aw heck, posts like this are why I try to stay away from FC... TY/FU to
@Herr_Dampf . Just put in my order...
Omron PID controller - 79.99$
20mm coil w/ male xlr - 45$
aluminum case - 23$
female xlr - 3$
16mm illum. push button - 8$
rocker switch - 3$
8amp relay - 4$
power cord and female power plug - free (already own)
---------------------
Total 165.99$ + shipping
Saved some money by ordering the 20mm coil which will fit my existing he nail, and by getting the fiberglass corded coil instead of the kevlar. Also could have saved more by using my own enclosure and ebaying the little parts. But the enclosure for sale has all the cut-outs already made..so lazy beats cheap this time.
Last edited:
Dramma Lamma
Looks like a job for!
This looks interesting.
http://www.alibaba.com/product-detail/deep-quartz-banger-enail_60123371212.html
Too bad I still have no e-nail coil.
http://www.alibaba.com/product-detail/deep-quartz-banger-enail_60123371212.html
Too bad I still have no e-nail coil.
herbivore21
Well-Known Member
So my dnail arrived. It is fucking epic! Such perfect taste, so easy to use, even works on my mini-rig without feeling precarious...
I will warn everybody that the direct inject pukinbeagle 20mm quarts nail, whilst tapered, will not sit particularly well in place on an 18mm male joint. Luckily, I had forseen this and am using an 18mm male to 14mm male adapter to save my piece from the heat, this also raises the nail to a good height right in front of your eyes.
I had the DIY dnail together in 20 mins flat, had my a quick couple of dabs of what was left on my dabbers from last time, then left for a very busy day at a music festival. First of all, the dabs were delicious. I have been dabbing this top notch, clear enough to read a book through THC bomb QWISO shatter for ages now, and nothing has ever tasted as good as this. See below for pic of said shatter.
My nail isn't even fully seasoned and it tastes better than anything else I've ever dabbed.
I would heartily recommend this product to anybody here, and am so stoked with my purchase.
Once I get round to buying a Mighty, I don't see a need for any new vapes/enails in my lineup
I probably will splash out on the 20mm Hive Ceramic nail when it comes out though lol
Here's a shot of my rig with her new adornment
I will warn everybody that the direct inject pukinbeagle 20mm quarts nail, whilst tapered, will not sit particularly well in place on an 18mm male joint. Luckily, I had forseen this and am using an 18mm male to 14mm male adapter to save my piece from the heat, this also raises the nail to a good height right in front of your eyes.
I had the DIY dnail together in 20 mins flat, had my a quick couple of dabs of what was left on my dabbers from last time, then left for a very busy day at a music festival. First of all, the dabs were delicious. I have been dabbing this top notch, clear enough to read a book through THC bomb QWISO shatter for ages now, and nothing has ever tasted as good as this. See below for pic of said shatter.
My nail isn't even fully seasoned and it tastes better than anything else I've ever dabbed.
I would heartily recommend this product to anybody here, and am so stoked with my purchase.
Once I get round to buying a Mighty, I don't see a need for any new vapes/enails in my lineup
I probably will splash out on the 20mm Hive Ceramic nail when it comes out though lol
Here's a shot of my rig with her new adornment
Last edited:
canj00digit?
All my days in a daze...
Baller' e-nail set-up, @herbivore21 !
Only took you 20min to DIY? Wow you must be handy with solder iron. I am handicapped with it, probably take me 20hrs.
Congrats!
Only took you 20min to DIY? Wow you must be handy with solder iron. I am handicapped with it, probably take me 20hrs.
Congrats!
herbivore21
Well-Known Member
No soldering iron required bro
herbivore21
Well-Known Member
It is game changing, I have made great concentrates for a long time now but this is the first time I've been able to really savour it every time!
SavageCore
Well-Known Member
Smiss have just announced on Facebook a new enail/vaporiser
Features:
Herb mode - 40c°/104°F - 230c°/446°F
Wax mode - 148c°/300°F - 482c°/900°F
The W100 2 in 1 vaporiser for concentrates and dry herbs
Features:
- Portable Power Bank: 16.8V, 4000 mAh
- Titanium heating component (Wax)
- Ceramic heating chamber (Herb)
- OLED Temperature Display
- Glass mouthpiece
Herb mode - 40c°/104°F - 230c°/446°F
Wax mode - 148c°/300°F - 482c°/900°F
Definitely interesting, actually kind of an appealing concept. I don't get why there is a glass mouthpiece on the vape hooked up to the water tool though.
KeroZen
Chronic vapaholic
Indeed it seems to be a battery-station-powered transportable desktop vape! There is a charger jack on the power bank and a listed battery capacity (4x Li-Ions judging from the nominal voltage, don't know if it's 4Ah total or per cell though), a rather unusual choice isn't it?
I hope it can work in pass-through mode too but the FM's don't support it, so I'm not holding my breath.
I hope it can work in pass-through mode too but the FM's don't support it, so I'm not holding my breath.
Silver420Surfer
Downward spiral
Soflo
Only birdshit and fools
I have no idea with the titanium nail. I got the domeless quartz nail from that same site with mine. It was like 40$.
Soldering.... yes I had to solder the wires to the mini xlr connector and the led button. I also soldered the tips of my wires for all off my connections..
that mini xlr is a bitch....
get your wire stripped and fluxed, then heat the solder on the wire and let gravity pull the silver down the terminal your wire is touching.
try and only strip a small amount of insulation off the wire. It'll help. I used 16ga wire and cut the count in half where the insulation was stripped.
Soldering.... yes I had to solder the wires to the mini xlr connector and the led button. I also soldered the tips of my wires for all off my connections..
that mini xlr is a bitch....
get your wire stripped and fluxed, then heat the solder on the wire and let gravity pull the silver down the terminal your wire is touching.
try and only strip a small amount of insulation off the wire. It'll help. I used 16ga wire and cut the count in half where the insulation was stripped.
MikeInMiami
Well-Known Member
my guess is that you can hit the unit without the water pipe by inhaling through the glass mouthpiece
syrupy
Authorized Buyer
Just took my first e-nail dab, on a unit assembled today, from a parts order placed a week ago, inspired by @Soflo.
Surprised how little soldering was required-- at the xlr/mini-xlr/aviation jacks (5 connections).The pid has screw terminals, and the power ports have tabs for crimped connectors. The included relay is easily replaced with one that comes with a base with screws. 5 touches with a solder gun minimum, unless you want to get creative.
Silver - I think the coil diameter is matched to the OD of the nail. So my 21mm HE nail is a tight fit on the 20mm coil. What's the diameter of the Omni?
Since I went with the larger enclosure, there's some room to add a feature or two. Like a circuit with an adjustable sleep timer to cut power to the coil in case of dab coma. Or remote power on/off... or....??
Edit: anyone want to buy a torch?
Surprised how little soldering was required-- at the xlr/mini-xlr/aviation jacks (5 connections).The pid has screw terminals, and the power ports have tabs for crimped connectors. The included relay is easily replaced with one that comes with a base with screws. 5 touches with a solder gun minimum, unless you want to get creative.
Silver - I think the coil diameter is matched to the OD of the nail. So my 21mm HE nail is a tight fit on the 20mm coil. What's the diameter of the Omni?
Since I went with the larger enclosure, there's some room to add a feature or two. Like a circuit with an adjustable sleep timer to cut power to the coil in case of dab coma. Or remote power on/off... or....??
Edit: anyone want to buy a torch?
Last edited:
Deadshort480
We're here to fuck shit up.
Don't get rid of that torch just yet. I own two electric nails and still fire up Quartz and ceramic all the time.
The Enail is sooooo titties though!
The Enail is sooooo titties though!
nathan1982
New Member
i recently baught a SPARK STATION. it is a canadian beauty very stable unit. well worth the money
canj00digit?
All my days in a daze...
@herbivore21, you were asking about the ceramic nails from Domeless.com and the side carb slot.
The idea behind it is to increase the low temp efficiency. You dab, then cap with sealed carb cap, then the only air that can be pulled in comes through the carb slot in the hot wall of the nail and then passes over the dish where you just dabbed on it's way into the intake tube. It actually works really well in my opinion.
But I think it's sort of a low temp feature and not needed nor really desirable probably on a traditional enail.
When I get one for a traditional enail setup it will be without the carb slot.
He is going to be coming out with a ceramic carb cap that stays on the nail and you just dab through a funnel. Then the hot air is pulled down the funnel straight into the dab puddle you just laid. Looks interesting, I am going to pick one up when they come out.
carb cap top:
http://instagram.com/p/uGrnu0nGHD/?modal=true
video of proto:
http://instagram.com/p/uv0iCgnGB-/
The idea behind it is to increase the low temp efficiency. You dab, then cap with sealed carb cap, then the only air that can be pulled in comes through the carb slot in the hot wall of the nail and then passes over the dish where you just dabbed on it's way into the intake tube. It actually works really well in my opinion.
But I think it's sort of a low temp feature and not needed nor really desirable probably on a traditional enail.
When I get one for a traditional enail setup it will be without the carb slot.
He is going to be coming out with a ceramic carb cap that stays on the nail and you just dab through a funnel. Then the hot air is pulled down the funnel straight into the dab puddle you just laid. Looks interesting, I am going to pick one up when they come out.
carb cap top:
http://instagram.com/p/uGrnu0nGHD/?modal=true
video of proto:
http://instagram.com/p/uv0iCgnGB-/