next generation e-nails?

Kanna_Kult

Well-Known Member
My first Gimido coil died after about 6 months of frequent use. I'm using a D-Nail Extended life flat coil now, not sure how long that will last.
Thanks for the reply! I think I'm gonna go the same route as you, my boy had an encased barrel coil from d-nail and it's the only coil he's ever had, still works flawlessly. Shoulda just got that one to begin with hahaha that's what I get for being a cheap bastard.
 
Kanna_Kult,

Kanna_Kult

Well-Known Member
Sorry to post back to back but I've looked around and only been able to find the standard dnail 120v flat coil heaters, I can find 10mm/16mm/20mm extended life coils but not extended life flat coils, is it just unavailable now or do they not make them anymore?
 

Gonzo_da_wind

Well-Known Member
Thanks for the reply! I think I'm gonna go the same route as you, my boy had an encased barrel coil from d-nail and it's the only coil he's ever had, still works flawlessly. Shoulda just got that one to begin with hahaha that's what I get for being a cheap bastard.
I had an Dnail encased coil cost about $125 it lasted around 8 monthes the somehow it shorted in the cord and broke my auber. blew the fuse and fried my SSR. Might have jus been bad luck but I never mistreated my coil.
 
Gonzo_da_wind,

DieHard

Accessory supplier
Accessory Maker
Still nothing really "next gen". Going on here. I have had my Errlectric unit for nearly 2 years with daily use and have yet to have any problems. The Errlectric MobilNail may be the next true "Next generation Enail".
 
I agree as far as the nail part and I feel the same about my Full Quartz Nail (Errlectric banger). Although I think the liger may be too heavy for some of my glass. But I was referring more to what's on the other end of the cord.
That's honestly part of the beauty of it. The weight or center of gravity is adjustable due to all the pivotal joints
 

psychonaut

Company Rep
Company Rep
Just got my flat coil and hybrid nail. Nice stuff.

http://m.dhgate.com/product/titanium-nail-domeless-gr2-g2-titanium-nails/230610242.html

The carb cap fits so snugly with a good draw. Tried it at 710f and it was lovely :love:

B1ZDJjG.jpg


EDIT: Sorry it its so messy =/ Took 9 days to get this through epacket.
 
Last edited:

Mangos

Well-Known Member
Hey guys got my enail. Looks great just got a question , it may seem stupid but this is my first enail and I'm new to the whole extracts methods.

I ordered a 20mm coil and nail but got a 10 mm coil and nail instead , not to big of a deal as long as it works properly .

Just wondering if there is supposed to be any gaps between the coil and the dish ? . I had a few dabs and it worked well , I'm really baked atm to be honest as I don't dab early normally- but I wanted to try the nail, so please bear with me if I make no sense .

Here's a pic :

XMgKJt6.jpg



Gap in front of the dish and the coil , don't know if this is normal or if it will prevent proper use ?
Would appreciate some advice, thanks .
 
Mangos,
  • Like
Reactions: grokit

Mangos

Well-Known Member
That looks like a 20mm coil
Thanks for replying, appreciate it. Messaged the seller informing him of the situation , hope it gets sorted. Still works fine , did a couple of small dabs and felt the effects nicely. Is it ok to use like this till I get a replacement ?

I had a feeling asking for a 20 mm dish and coil would confuse matters.

Edit : Took a pic of the dish inside the coil , it seems to be the same size ?? If the coil was 20 mm wouldn't there be a bigger gap ?

I honestly have no clue now. I think its the right size but just may be a sloppy fit ?? Just need to now so I know whether to tell the seller of a fault.

ZChY92Y.jpg
 
Last edited:
Mangos,

mrbonsai420

Accessory Maker
Accessory Maker
Hey guys got my enail. Looks great just got a question , it may seem stupid but this is my first enail and I'm new to the whole extracts methods.

I ordered a 20mm coil and nail but got a 10 mm coil and nail instead , not to big of a deal as long as it works properly .

Just wondering if there is supposed to be any gaps between the coil and the dish ? . I had a few dabs and it worked well , I'm really baked atm to be honest as I don't dab early normally- but I wanted to try the nail, so please bear with me if I make no sense .

Here's a pic :

XMgKJt6.jpg



Gap in front of the dish and the coil , don't know if this is normal or if it will prevent proper use ?
Would appreciate some advice, thanks .


I believe that is a 20mm, either that or the 16mm. It's not a 10mm, those are for nectar collectors and are really tiny.

That is as good as it gets with that coil/nail setup. You may have better luck flipping the coil since the temperature probe reading is taken at the tip and that will be closer to the dish, but I doubt it will make much difference. Most people use the Flat coil for this type dish (Halo clone) and a Liger for a barrel coil like you have. But this should work just fine, worse case scenario is that you have to turn your coil up a little more than normal to get your dish up to temp which is no big deal at all. Just play with the temps, you may have to go over the 700 degree mark depending on the heat transfer. Just remember that it's not the coil temp that matters, just the dish temp. So you may have to go to 750 on some setups for the dish to reach 675. I'm sure once the body gets good and heat soaked you can turn the coil down below 700 and still get good hits. My temps might be off since I don't have this exact configuration.


Check out this last round of CCA stuff! These next gen inserts are top notch quality and the new variable flow storm cell cap is SICK!

EDA85E6E-FF57-4448-858B-6D4DAF2096D0.jpg


EE31CB46-512B-41C3-8445-9CDE78266248.jpg


9C6390BE-29B8-434E-A537-8F675A0AD633.jpg
 

garymon

Member
My pid/nail/coil kit arrived tonight:
http://www.dhgate.com/product/quartz-flat-10mm-coil-enail-kit-d-nail-dnail/376329298.html

Shipped in less than a week. Packaging was sound. Everything looks good.

This is my first setup like this. Upgrading from a 710 domeless. Started off with some Clear. Set temp to 650 for first two dabs. Nice flavor but I didn't feel like I got much of a hit. Turned it up to 710 for the next two dabs. That hit like I expected. Feeling very medicated now.
 

Mangos

Well-Known Member
My pid/nail/coil kit arrived tonight:
http://www.dhgate.com/product/quartz-flat-10mm-coil-enail-kit-d-nail-dnail/376329298.html

Shipped in less than a week. Packaging was sound. Everything looks good.

This is my first setup like this. Upgrading from a 710 domeless. Started off with some Clear. Set temp to 650 for first two dabs. Nice flavor but I didn't feel like I got much of a hit. Turned it up to 710 for the next two dabs. That hit like I expected. Feeling very medicated now.

Would you mind posting a pic of your setup ? Got the same product but asked for 20 mm accessories, but the dish feels a bit loose around the coil , I posted some pics above, I showed the seller and he is claiming that that's how it fits but I would just like some confirmation before I release payment to the seller thanks .

Sorry for bringing it up again, just want to know if I have the wrong sized part or if its just supposed to be fairly loose .
 
Last edited:
Mangos,
  • Like
Reactions: b0

Justpassedu

Well-Known Member
Hey all , I have not been around this thread in a bit but I am still looking for a dedicated Enail , My Evo has been holding me over nicely and I ordered a few more nails for it but I'd still like something for some group use. So I narrowed it down to not wanting to order direct from china/dhgate , while the prices are attractive and the combos you have all been posting look nice I want something with a U.S. warranty . I have finally narrowed down my choices to the high5 kits , a company called Boss with some really nice looking cases and the edabsdirect. I know I want a quartz dish. They are all in a similar price point and i'll prob pull the trigger shortly and will be sure to post a review of whatever I choose. Do you all suggest a 16mm coil or 20mm ?
 
Justpassedu,

psychonaut

Company Rep
Company Rep
I suggest a flat coil and a quartz hybrid nail, but you can always get that later. I started out with a 20mm heater and a ti nail. Worked great but I like the flavor on quartz better.
 
psychonaut,
  • Like
Reactions: grokit

Justpassedu

Well-Known Member
I suggest a flat coil and a quartz hybrid nail, but you can always get that later. I started out with a 20mm heater and a ti nail. Worked great but I like the flavor on quartz better.
I plan on going Quartz from the get go , never really liked dabbing off anything made of metal.
 
Justpassedu,

NevadaPradah

Active Member
Cant decide between a Liger or D-Nail sic setup. i like the looks of D-Nail, but the larger Liger surface area is appealing. Is there a difference in efficiency/performance? Also does the Liger titanium banger body effect flavor?
 
NevadaPradah,

Silat

When the Facts Change, I Change My Mind.
Silat,

Gn0sis

Well-Known Member
Cant decide between a Liger or D-Nail sic setup. i like the looks of D-Nail, but the larger Liger surface area is appealing. Is there a difference in efficiency/performance? Also does the Liger titanium banger body effect flavor?

i went with D-Nail for the sapphire insert and eventually the full sapphire dish. as for surface area, in comparison to a Highly Educated Infiniti nail large dish, the d-nail SiC dish is almost twice as big.
 
Gn0sis,
Top Bottom