Dani Fusion by Battery-free Ganz

DgN'R

I'm No Superman!
I'm really impressed with the Dani Fusion 2.0 Artemis :love:





I use it with my Blazer FireFox on the high temp zone (add +5 seconds after the click) and it takes about 25 seconds in all. It offers good retention and I usually get four tasty draws :nod:

The only negative point for me is the induction heating with the Wand. Although the cap is magnetic, the performance is quite poor. I use it by inserting it from the bottom this way (at the maximum temperature of 430°C), because from the top it's even worse (and it would probably take two consecutive heatings to achieve the same result):



This way, heating takes about 1 minute 45 seconds.. in comparison with my TA2 and inserting it in the same way (and at the same temperature), it takes about 1 minute and 15 seconds..

Anyway, it's the best vape pen I've tried so far, and the design/finish is so incredible.. truly magnificent work :clap:
 
We put beeswax on the wood and clean the inside with an ISO-soaked stick.
Pipe cleaners here. Can be bent double / triple, as desired. Then a little wax on the outside, once done.

Although the SS sleeve isn't removable (unless you've got a mechanical press -- and don't do this!), I find my Dani pretty easy to clean. Although I do keep the metal tip assembly mostly in one piece (the two pieces that you turn to adjust airflow, which are very hard for me to pull apart, and also difficult to visually line up the two holes for max airflow, when reassembling).

Just got back home from 3 month trip. Took Dani, Anvil (and Ispire for both), plus a desktop ball vape. Which did I wind up using most, during that time? The Dani (although I've since switched back to the ball vape, upon returning home).
 

spazzoo

New Member
Just figured I'd update again with my ongoing saga of the Flare. BFG has been pretty slow to respond... the second unit works fine initially but it seems like as soon as any of the batteries drop below a full charge the unit starts to lag with its heating cycle. I'm hoping they are able to resolve this but it's been a loooong conversation so far. Tbh at this point it's annoying enough to make me avoid using my Fusion bc I don't want to bother with it
 

TedJones

Well-Known Member
Just figured I'd update again with my ongoing saga of the Flare. BFG has been pretty slow to respond... the second unit works fine initially but it seems like as soon as any of the batteries drop below a full charge the unit starts to lag with its heating cycle. I'm hoping they are able to resolve this but it's been a loooong conversation so far. Tbh at this point it's annoying enough to make me avoid using my Fusion bc I don't want to bother with it
That’s a big bummer :mad: Assume you’re using quality batteries in there? Not wanting to torch it either?
 
TedJones,

spazzoo

New Member
That’s a big bummer :mad: Assume you’re using quality batteries in there? Not wanting to torch it either?
They are standard batteries from Amazon but had solid reviews, and I checked with BFG before ordering that they'd work well. And nope, not torching it. I do 85W for about 40 seconds for the first heat, then it only takes 20ish seconds for subsequent heats.

Now BFG wants me to send in my Flare AND my Fusion for them to examine, no mention of a replacement or timing for it all. It's a lot to ask tbh. At this point I'd almost rather just take a refund and be done with it
 
spazzoo,
  • Like
Reactions: stonedBBer

MaWi

New Member
I absolutely don’t know who could be interested in it, but I like to shout it out: I FUCKING LOVE MY DANY FUSION 2!

It‘s the first Vape that satisfies me at least to 99%. I own Simrell, Tempest ( not satisfied at all), Tiny Might… Dani fusion 2 is the best!
 

TedJones

Well-Known Member
They are standard batteries from Amazon but had solid reviews, and I checked with BFG before ordering that they'd work well. And nope, not torching it. I do 85W for about 40 seconds for the first heat, then it only takes 20ish seconds for subsequent heats.

Now BFG wants me to send in my Flare AND my Fusion for them to examine, no mention of a replacement or timing for it all. It's a lot to ask tbh. At this point I'd almost rather just take a refund and be done with it
I’d recommend trying different batteries first if you don’t want to send it all back. Molicel from reputable vendors like illumn.com or imrbatteries are great. I’ve been buying from them for years. Might be able to get them cheaper elsewhere, but I’ve heard they’re more or less “2nd quality “.
 
TedJones,

prayerplant

Well-Known Member
I absolutely don’t know who could be interested in it, but I like to shout it out: I FUCKING LOVE MY DANY FUSION 2!

It‘s the first Vape that satisfies me at least to 99%. I own Simrell, Tempest ( not satisfied at all), Tiny Might… Dani fusion 2 is the best!
Pleased for you, shout it out!
Out of my vapes that are pretty much all manual, I use my Fusion 1 more than any other by a long way. I use the head on the Tempest stem using an 8mm/9mm adapter. 😁
 

prayerplant

Well-Known Member
Who makes 8/9mm adapters these days. Tincturous is always sold outb
Bargain at £7.50! Always pleased to buy from these guys
 

vapegod

New Member
Is there any shop in the EU where I can order that thing? And is there any adapter so that I can use a Dynavap head with my 9mm Dynavap Fusion stem?
 
vapegod,

tester21

Member
Any significant difference between shorty and regular length stems as far as function/cooling? Trying to decide which one I want.
 
tester21,
Top Bottom