Glad you settled it @invertedisdead , mine will arrive any day and a package from sweetleaf to load it with. Let us know your settings as you progress.
All di best.
All di best.
AVS Molecule RDA
- Thread starter Kanna_Kult
- Start date
I just can't get the damn cap off. Even oiling the O rings so far does nothing. I have to unscrew the housing, use a ram rod to pop the cap off since installing directly can crack the quartz bowl. I also find it pretty hard to load but I've only tried diamonds so far. It does taste pretty damn good so far, haven't been blown away by the vapor production.
tennisguru1
EXCELSIOR!
I got that bubbler attachment in the mail, as soon as I get it will be
last time I have to use that tiny mouthpiece.
Going to use that base to mount my all glass mouthpiece & straw
I use on Sai as the easy on & off to load & hit much easier.
It should work also with the Mole's Quartz Cups which are now here.
Should have the whole setup by weekend.
Hope it hits near as great as the Sai's QC, fingers crossed.
I would check the resistance first and see if you can strum in TC like the AVS video. If not go for wattage mode, I think 15w is a safe starting point.
My mods are all set up in Arctic Fox to Re-Read the resistance by pressing in the -+ buttons at the same time, nice little feature instead of unscrewing the atomizer.
Don't be surprised if your cap is TIGHT as heck for a bit. Mine is just now starting to loosen up. The advice from @al bundy about wiggling it gently worked perfect. I was skeptical to try that at first just due to the quartz fractures people were getting screwing the housing + mouthpiece on at the same time, but I don't think mine would have ever started fitting without that little wiggle. I "twist" the mouthpiece when installing it to the housing.
I'm hitting mine at 30w lately in SS316L 380-410F, trying to decide if I get more reclaim at lower or higher watts. At lower watts there's drip through, at higher power there's splatter, so I'm trying to find the happy medium.
It actually tastes a lot better than I expected, the flavor is pretty impressive on it, IMO not completely on par with an all glass vapor path hit, but 360F-390F has some pretty legit flavors.
My mods are all set up in Arctic Fox to Re-Read the resistance by pressing in the -+ buttons at the same time, nice little feature instead of unscrewing the atomizer.
Don't be surprised if your cap is TIGHT as heck for a bit. Mine is just now starting to loosen up. The advice from @al bundy about wiggling it gently worked perfect. I was skeptical to try that at first just due to the quartz fractures people were getting screwing the housing + mouthpiece on at the same time, but I don't think mine would have ever started fitting without that little wiggle. I "twist" the mouthpiece when installing it to the housing.
I'm hitting mine at 30w lately in SS316L 380-410F, trying to decide if I get more reclaim at lower or higher watts. At lower watts there's drip through, at higher power there's splatter, so I'm trying to find the happy medium.
It actually tastes a lot better than I expected, the flavor is pretty impressive on it, IMO not completely on par with an all glass vapor path hit, but 360F-390F has some pretty legit flavors.
Thanks @invertedisdead , after your mods having weird resistances youve mastered the mole.
I will post my ease ( or not) at getting going.
I will post my ease ( or not) at getting going.
my resistance is .34 I've gone 25 watts up to 430 Fahrenheit, No vapor at all it's just making the stuff bubble a teeny bit.
I should be locking my resistance correct?
it's locked at .34 after some strumming of the installed coil is that anywhere in the ballpark?
I should be locking my resistance correct?
it's locked at .34 after some strumming of the installed coil is that anywhere in the ballpark?
subway13029
Well-Known Member
Yeah def lock the resistance once you get it settled in..and I was having great results and I was unscrewing the housing every time I loaded it up and then when I realized that the top cap actually seal inside the lip of the quartz cup that I started actually pulling the cap off to load and the results got better and my readings stayed more consistent..
I’d say to get your resistance higher than .34...when my resistance wasn’t right I would leave cap off and my wax would boil away with no vapor.
I’d say to get your resistance higher than .34...when my resistance wasn’t right I would leave cap off and my wax would boil away with no vapor.
subway13029
Well-Known Member
When I went camping last weekend and went to walk and take some rips..it was too cold and wouldn’t hit right..lolOkay weird I just let it sit for a bit it came up at .39, locked it and got an amazing rip
Edit
It may have been a bit cold from being in the mailbox.
It's working great right now!
And yeah if my resistance is off sometimes my coil will be loose..but was from unscrewing housing..
tennisguru1
EXCELSIOR!
Hey buddy just picked this up from Mole creator
From the creator
VapeMore4LessAVS Molecule Creator • 18m
I'm ordering a jet stream too haha... I saw that post with dual molecule coils and now I need one! That would be perfect to hook to my rig, or just one giant hex core coil in the jet stream, not sure if it will fit but I'll try it and share. Weve been hit with so many delays on the quartz. On that note though, what I've done is created a SS crucible that drops into the quartz bucket and is ultra thin, instant heat and low heat retention. The outer quartz is to help act as a heat refractory. Then you can dab right out of the 316lss bucket or drop the revised quartz bucket we're making into that instead of trying to place it perfect on the coil. The main issue I'm having with our quartz is boil over and so I'm making it taller. Quartz is a new thing for us and I jumped the gun on that and am paying the price for it. I got caught up in the excitement of the molecule with everyone and just wanted to make everything people wanted. I've taken a step back and am properly testing everything as I did with the molecule. I'm currently testing the AFC and it's amazing. I'll let people order it soon but not until I 100% know when I'll ship them. We definitely experienced some growing pains but I'll have business running normal very soon and everything in stock, probably won't do a preorder ever again haha
tennisguru1
EXCELSIOR!
szai
Well-Known Member
Is anyone aware of a high quality but tiny box mod for the molecule? I'm using it in wattage mode after having some issues with my joyetech evic dual. I'm enjoying the hell out of it just running it between 13-15 watts and pulsing hits. The first hit is between 5-8 secs then after around dry hitting for three secs pulse and additional 2-3 secs and continue doing in until you're done!
https://www.instagram.com/p/Bp8Y2yMjyqd/?utm_source=ig_share_sheet&igshid=x40gpwprwovk
https://www.instagram.com/p/Bp8Y2yMjyqd/?utm_source=ig_share_sheet&igshid=x40gpwprwovk
Last edited:
tennisguru1
EXCELSIOR!
So I assume you are using AF and not stock firmware, ok?
I just popped my Mole on Dual Evic , running AF TCR#92 @19watts
temp 39- 420 resistance locked a .386 works great full 15 second pull
smooth, no burning, original coil 5 grams thru.
I have never unscrewed it, always pull off top to load.
Installed on low profile black heat sync, TIGHT, lol.
Moved to 4 diff mods.
Best was Espion 200 Dual Red Panda (color AF) overkill but nice.
Might be really good for bubblier balance.
Evic Two Mini - AF very good fit TC great
Evic Dual & Lavabox m DNA 75
Istick pico gifted to friend he likes it also running AF
szai
Well-Known Member
Thanks for the suggestion I did that and it worked! Wow this thing is fantastic in TC ma!
Does anyone have a source for some narrow heatsinks?
tennisguru1
EXCELSIOR!
You're very welcome :>)
Smallest I found was on FT and they were 18mm out of stock
if you find smaller, let us know ty
It would work fine, although I prefer to use oils like distillate or co2 in a ccell cartridge for no reloading.
tennisguru1
EXCELSIOR!
The Mole Bubblier Adapter + Sai QC cup Motar + Whip for filming
I tried using the old mole cups but their too short & spilled over.
New ones are higher ones are shipping out soon.
Just starting playing, but it looks good.
With just .01 shatter & I couldn't finish it.
Don't have a clue how to dial in TC, but just
pulsing in wattage not a bad start.