AEON Glass by jhanpixel
- Thread starter NewVape
- Start date
Anonymouse
Sith I care
Hrm, that's worrying. It appears those particular nails aren't American after all. I never questioned it since they're the right colour for Ti, and while they are heavy, I put it down to the massive thickness. On investigation, mine is mildly magnetic (will just barely hold a rare earth magnet) so contains at least some iron, so is also definitely not a non-alloyed Ti, if there's Ti in it at all. I'll see what colour sparks it strikes on the grinder tomorrow and check.
The original point stands, though, in that a (REAL) Ti nail is a healthier option. I guess you gotta go Dab Essentials or InfiniTi after all, but they seem a bit enthusiastically-priced compared to cost of materials.
Generally a resistor of some sort, same as with a ceramic heater, though you have the option of using a Ti coil directly as your resistor/heater/exchanger instead of pressing an external heater against the outside of the Ti exchanger. Or you could get fancy and run an induction coil directly around a Ti heat exchanger inside a glass tube. You'd have to deal with thermal expansion, though, but shouldn't be too big a deal to contrive something.
Remember Ti is just better at passing on heat, and can hold more of it. You still need the wattage to produce the required heat in the first place, so with modern battery tech the only way a Solo could work like a Cloud is if it's only good for like one hit or so. Could probably rig something you heat with a torch, though, that'd have the right heat capacity; blaze the outside of the exchanger block then suck air through the finned channel/s inside. Not as cool as an electronic system with sensors that alters heater power with draw speed, though, but as a portable option it offers lightness and compactness. Something like a Lotus made of pure Ti, for example. Or better still a Lotus with a GonG (TonG?) end.
Let's take our TI nail talk over to the appropriate thread
Jahn doesn't need his thread derailed anymore.
haha i don't mind the free bumps
heres a pic of nano ratchet we made for 4/20
hope everyone had a safe 4/20
heres a pic of nano ratchet we made for 4/20
hope everyone had a safe 4/20
Anonymouse
Sith I care
Is the new stuff on iOffer yet?
nope all prototypes for inhouse use for 4/20 =)
we took down the sidecar due to being a bit TOO similar to the Hitman Brilliance Sidecar
won't be producing that style anymore.
have a few sidecar designs in mind tho, so we'll see what happens
we took down the sidecar due to being a bit TOO similar to the Hitman Brilliance Sidecar
won't be producing that style anymore.
have a few sidecar designs in mind tho, so we'll see what happens
Anonymouse
Sith I care
Triple inverted-showerhead bubbler, pls.
You could call it a "wedding cake" perk, 'cos that's what they look like in operation.
You could call it a "wedding cake" perk, 'cos that's what they look like in operation.
Roger D
Vapor Wizard
like this?Triple inverted-showerhead bubbler, pls.
You could call it a "wedding cake" perk, 'cos that's what they look like in operation.
Anonymouse
Sith I care
Sorry, triple nested inverted-showerhead.
Like this:
Once the water moves up into the showerheads it forms three stacked cylinders of decreasing diameter, like a wedding cake. Heck, go nuts and try for four. It sure looks like there's room to widen the first stage a bit, which in turn provides room to widen the next and the next. Plus you could always use a wider can I guess; volume would still be fine if it was stubby enough.
Would prefer bubbler to tube, though, ideally with removable mouthpiece, but if not with a mouthpiece placed so you can watch it work as you inhale. Oh, and way more slits than the above example.
Like this:
Once the water moves up into the showerheads it forms three stacked cylinders of decreasing diameter, like a wedding cake. Heck, go nuts and try for four. It sure looks like there's room to widen the first stage a bit, which in turn provides room to widen the next and the next. Plus you could always use a wider can I guess; volume would still be fine if it was stubby enough.
Would prefer bubbler to tube, though, ideally with removable mouthpiece, but if not with a mouthpiece placed so you can watch it work as you inhale. Oh, and way more slits than the above example.
Roger D
Vapor Wizard
Anonymouse
Sith I care
Side car !
I prefer removable, as it lets you switch from symmetrical to sidecar just by turning it in the joint. Also you can stick an M to M and a j-hook on there to get real low and get a good view of the action.
Or stick a whip on it so you can lay back in bed... (assuming it's plugged into a vape)
Or stick a whip on it so you can let a bunch of stoned friends use it without worry...
Or stick a whip on it so you can chain it into another piece...
Options!
Thunderclees
Well-Known Member
I just got my 10" bent neck stemline. It's fantastic!
colieglass
Well-Known Member
where ya been jhan?
at the movies - iron man 3! rocked!
anyways V2 finally in production and loads more prototypes to come.
pics when i have a chance
peace
anyways V2 finally in production and loads more prototypes to come.
pics when i have a chance
peace
colieglass
Well-Known Member
wouldnt you rather just wait for the pics?
that herb guy
Well-Known Member
The obvious answer is no, until the pics are available. Then we'll agree.
I'm curious too.
I'm curious too.
colieglass
Well-Known Member
well, wouldnt his time be better spent actually making the pieces other than describing them to you? i think we should exercise some patience and let the man work instead of tapping away at a keyboard all day. jmoThe obvious answer is no, until the pics are available. Then we'll agree.
I'm curious too.
captain procrastination
New Member
I'm looking forward to see what comes next. Also looking to see what you make too colie cause I'm thinking about getting a travel piece and a black and slyme recycler you hinted at sounds sweet.
colieglass
Well-Known Member
we already did our run of black and slymes, they sold very quickly, but i will throw you one together when youre ready... thanks for the support man, but call me andrew.. colie is the name of my company 
Stemline honey finally released.
V2 hopefully later today or monday if i get a chance
still processing in utube
**** now playing ****
**** now playing ****