Search results

Spare coils. I was trying to match the exact wire but nowhere seemed to have it, all out of stock. Yeah that's fair enough. Like I said though, who knows what the real temp is. The mod is estimating the temp based on the settings you put in(changes in current/resistance etc). It's not...

Yeah, if you've checked the contact screw of the impcog and that looks ok, that's probably just what the resistance of your coils is. Dave may have found the exact coil gauge he used when he started harder to find in the last batch. I couldn't find any when I tried to get spares. My max vaping...

A quick update about the config file: Although I've been using it myself at the weekend without any problems, when I cleaned up my config file before uploading(removing the profiles for other atties etc), the pi-reg settings didn't copy over to the profiles they replaced for some reason. So you...

That seems a bit low for the stock coils. I noted down somewhere that 0.22 is what the resistance is supposed to be(probably read that somewhere on this thread), I'm not sure if that's the cold reading or the recommended resistance setting from mistvape/dave. I suggest you check the contact...

I would r I would recommend the generic 14mm OD High borosilicate glass tubes I found on Ali. 50mm works fine. 100mm and 200mm+ available on the same link(5pieces per order). 80mm works well too if you like it a little cooler. 40mm and 120mm available on the same link(10 pieces per order). I...

So, I've tried two different silicone O-Rings with a 2.5MM CS. 14mm ID and 13mm ID, both of which were too big, to my disappointment. The 13mm was surprising, as that should have gave it a 18mm OD(same as stock). Perhaps this is because the o-ring is thicker and doesn't sit quite as far back as...

Ordered a couple of silicone O-Rings the other day. Couldn't find any 13.5mm ID ones as I'd hoped(always the way) and I thought 13mm would be too small, so I've gone for a thicker cross section(2.5mm and 3mm) which hopefully means it wont be seated as far back as the stock one was. I cannot...

Let me know how you get on with it. With your different profiles, do you also check the device monitor while you're using it(empty chamber), to see if the voltage and temperature reading stay pretty stable(no big spikes or drops)? Or are you just judging it by how good the hits are?

Ok, so I ended up having to remove the screw to measure it. Tried chiselling a grove for the screwdriver to get purchase but in the end some needle nose pliers worked. I measured the contact screw at 18mm long, the screw diameter 2mm and the head diameter 5mm. I also removed the O-Ring while I...

Yeah, it's my go to atomizer now anyway(hence why I'm buying spares, as I want to keep it working for a while). I think most of the wear was there when I bought it from the previous owner, hopefully it's an easy part to replace.

I encountered some new problems this weekend with the resistance readings of the coils being all over the place and atomizer not found errors. Removing the atomizer and screwing it back in place worked eventually but I think the 510 contact screw is probably the issue. I flipped it upside down...

Just looking to add some more spare baskets and perhaps replace the red O-ring. Anyone got any good recommendations for the baskets? There's a 10.7mm diameter on the originals according to mistvape, so I'm thinking 11mm might just squeeze in. I can only seem to find 10 and 12mm personally...

Just an update, in case anyone was thinking of pulling the trigger on the glass tubes I found, to have as spares. They finally arrived today and everything fits as expected(tube and baskets inside the tube), so the thickness must be 1.5mm. It was well packaged, the tubes were taped tightly...

At least you're not a clumsy drunk oaf, who thought it was good idea to refill your imp in the kitchen(tiled floor). I had to crawl on my hands and knees finding all the glass balls before I could sweep up. :lol: I have just ordered some 80mm ones instead. I might be able to fit all 10 glass...

Haha, the dimples(shelf) and the roundness were two different points. I was just talking about the lip of the tube itself there. Although, maybe I'm overthinking that, even if there is a difference, it could be easily sanded and smoothed out. After asking the seller if they could do me some...

Nah I got a refund on that. Thanks for the suggestion though.

Fair enough, thanks for the heads up.

The shelf. I figured it was for the deeper baskets. It doesn't seem close enough to the heat source that far back, meaning you have to jack the temperature up a lot more. I've been getting good results my way. Gentle why? Have people on here tried them out and had bad experiences?

Yeah I guess so, it's just going to be missing those dimples at the bottom and the rim probably won't be as rounded, to make it comfy for your lips but I will be using the glass adapter anyway I guess. Which reminds me, I will have to order another of those divine tribe glass tips because that...

Oh yeah i didn't think that through, obviously the stem part is a standard diameter. Does anyone know the exact measurements of the original stem? Outer diameter, inner diameter and length. I've just eyeballed the inner diameter of the chamber at 14mm. The airizer stem that didn't fit has a...