Search results

I'm with @Vaporcussion , but I've gotten in a habit of pushing down between the center dimple and the outer ring. Then I grab it with tweezers or get something underneath it. It does deform it a little, but I think anything I've tried has lol. A shot glass on it in the bathroom where I clean and...

Vaping very small amounts.

Always! A quick ISO or PBW rinse an RO rinse and into the dryer because I'm impatient. Before it's asked, I bought dryer mesh bags that were originally intended for the SB caps, but are now used for anything unbreakable. I keep the lint trap and ductwork very clean and have never seen...

Just for my own clarification, I went and dug out my directions, there's no version or date on it, but it reads the same as what @Baron23 posted in post #2305. So, while what has been passed along may have changed some, the official directions haven't. I also noticed again, forgot about this...

That's almost a guaranteed no, they won't fit. I held the bent stem up against the GH oven opening and it's not quite the diameter of the whole barrel. The F2 capsules would need to be extremely loose, like rattling loose to fit the GH. Did get my Ti GH back that went in for RMA beginning of...

It's really hard to tell from the picture, but depending on the steel used, especially for the bars, that structure may be extremely strong. If the bars and cross members were annealed, I don't doubt a 12T rating. When I see all the shear points on the standard presses made from cold rolled or...

For quick cleanings I don't disassemble, but every other or third I do. The silicone pieces in the top and bottom that seat the glass need it occasionally to keep the flavor at its best. There were directions early on in the thread and I followed those, it was a little nerve racking until I...

I've read somewhere that they were intended to be single use, I've used mine countless times. I only toss them if I mangle one opening it, they hold up fine. Also never seen a 400 pack, just 40. I'm hoping these hold up as well, interested in seeing how firm/flimsy they are being all screen...

Cab I ask, have you used one?

I'm in for 10 as a trial. Not as cost effective as the S&B aluminum caps, but if they work as well or better, the quick heat up time and pocketability of the F2 should offset it just fine for me. I'm also interested is seeing their size, physical dimensions and volume. I'm thinking of milling...

If you're handy or adventurous, make your own! Oogoo (homemade Sugru) or even PlasticDip (check for health concerns) wouldn't be too tough. I've made 18mm caps for the Mi and such so I could pre-load stems, battery caps for the MFLB and 18650's, once you play a bit, it's pretty easy.

I love the thought, but the first thing that came to mind is that the reclaim on the back will just work it's way down the short vapor path. Let us know how this works after a few!

Blocked here too... My first thought was you were hitting it hard and fast, timeline says ?Maybe ? All my first attempts have been home grown that I purposely trimmed and left leaves that were covered, and it's only been two strains, but 10% sounds low. Could it be strains or technique...

I could tell you how I use it, but I'd be spoiling all the fun. Read some, wait for it to show up and play! It's only complicated if you make it that way. Run into any problems and everyone here will help. And save some good stuff for when it shows up, it'll be even more fun :ko:

These aren't going to be as cost effective to manufacture as thin, stamped aluminum from what I've read, but it would be nice !

I'm with @vapviking , some feel it does, I don't think it was noticeable.

I kinda think that's something best answered by FJ, himself. I'd PM him here and/or send him an email. Welcome to the ever growing team!

If you have a spare "finer" screen, like what's in the bottom of the oven, that also fits and can be used in the cooling unit (CU). Many of us make that change intentionally because it helps keep the CU a little cleaner. If bought new, I think it comes with some spares so you don't have to wait.

You mentioned "with the pressure I use", can I ask what that is? I've only got about 6 presses with my starter press, everything else is just from reading, but..... I've found in multiple places that when you get over 1600-1900 psi, you start getting into lipids and waxes being extracted, and...

Nomad 028 paid up and very happy :rofl: Also very excited for round 1 peeps!