Search results

As long as you don't go crosseyed! I think it would be too heavy honestly. I would go slighlty bigger at least. I have a mini dab rig about twice the size of that one but I rarely use it. I have been primarily using a rattle can which is very much like a mini rig in that you fill it with so much...

Unfortunately SiC can and does break. Fortunately it is not common and usually involves user error and some kind of impact while hot. At least thats how it happened to me and I recall reading another similar story in this particular thread. Sorry for the buzzkill.

The Triton is supposed to be released in March according to G's last update. I asked W9 support about the link and they said its not available and couldn't advise of when it would be available. The link has also been changed to require certain permissions last I checked.

Where did he say that? I just skimmed the video again and at 5:15 he is saying how remarkably consistent it is. Did he say somewhere else that it is not?

That dish does look quite large! Where is @Sneaky Pete to tell us more? I would like to know the size of the dish. It looks like a regular 510 thread possibly on the atomizer. Can you verify that @SneakyPeteVaporizers or is it a different size? Maybe its 610? It also looks like it only heats...

You can buy flat insulation plates from Low-Temp. I believe they were pretty cheap. I got one for the bottom and wish I had one for the top where the ram comes down on the plates. @mixchu69 You can buy a PID with the heater cores that all the newer setups use from ebay or most of the kit...

Take it easy on G. Do you not see how much we push him to release things now and not later. None of us want to wait half the time. G was most informative about the Trinity tanks here on FC. Most people would not know what the Trinity is if it werent for this site or Bubbleman so it makes since...

I ordered an S-Body C3D1 from element vapes right before Christmas. They seem like a good company. No problems with my order. I just don't understand eacribe! @almost there Element Vapes has the steam engine also. I was checking it out too

I had one on my DTV3 that I modified to use a Terra2 cup. All I did was take a dart from the Puffco Plus and put a piece of silicone tubing around it. I then push the splash gaurd out of the DTV3 mouthpiece and installed the dart wrapped in silicone into the mouthpiece where the splash guard...

Is that the S-Body CP2something? You might want to go with a more simple chip honestly for your first Mod. I am finding it hard to use the escribe program to create my own TCR settings. I honestly found my Evic Vtwo Mini a lot easier to use.

I might have something I can send your way if you want them. I know I have a couple smaller ceramic cups. I might have an extra quartz cup also. I will take a look and let you know.

I am also struggling with the XL carts lately. The 1mm heater I was using with straight Rosin and shatter stopped working after about 1.5-2 grams. While I was using this one I had another 1mm XL heater in a cart with Distillate I pulled out of some pre-filled carts. I would say I had run about 2...

Yes but only because I have not found a way to pocket and stealthly operate my DNail sic dish, PID and diffusion pump.

My mother has referred to all 3 of my children as angels. Spill some milk...pray. She loses her keys...pray. Cop pulls her over for speeding...pray. Running late for a meeting...pray. Left a light on...pray. Cannot remember directions or designation...pray. Gonna be inconvienced by a long...

Source is not stocking SiC cups anymore. They were too thin. I had two break on me during initial heat up. After the first broke following their recommended TC settings they replaced the first cup I had and advised of new lower recommended settings. I noticed they changed the settings or their...

What about the ID? I am guessing the guys using glass bowls are sliding the coil nut over the bowl? I have been putting off buying in to the FP for quite awhile now which seems to have paid off since the WA has come out. Now if I dont need a bowl and can use a glass bowl I already have laying...

Does anyone know the outside diamater of the 20mm Center Post Coil Nut (3066)

I tried creating a couple of profiles in escribe on my work computer but being it is at work I cannot spend a lot of time on it nor can I test out the settings right away. I also do not understand how to create a custom TCR in escribe. If you can elaborate on how to set a custom TCR, I probably...

Can this DNA mod be set without using Escribe? Like can you choose your own TCR settings from the box or do you have to hook it up to a computer and add in TCR presets? I have a DNA 250 mod that only works through the computer and creating TCR profiles in escribe is more than difficult for me...

When are you going to start a thread for the Fierce? A month ago you said you would have pictures up in a week. Is there any new information or pictures you can start a thread with yet?