Search results

Should treat the same way as the PSM. The only real difference is the battery type. Dissasembly is pretty self-explanatory once you remove the screws. This BMS does not have balancing abilities but does have protection if any cell gets too far out of voltage range. Many do confuse this as a...

Would work. The only problem is you would have to remove the battery from the PSM to access the 4 pin connector.

Yes, a JH (home unit) replacement. A 1/2 - 2/3 size PSM encloser would be possible because of the lack of a battery. Would just give the two units the same look. And saves me making two driver configurations. Those PSM enclosures seem very popular on many sites in my searching but no other...

Sorry but only a 3S charger should be used. And I recommend sticking at a 1 amp charge rate. For the most part, you can really only easily get online but the good news is they are not expensive to buy. Always a good idea to get a 3S car charger version as well if you're on the road a lot. ;)

Nice video! Must have been early in the morning judging from the lack of people. Those Bluff grounds usually have tons of picnics going on. You would get into huge trouble these days as that coastline is classified as a no-fly zone now. I have a Hudsan H109S which I've had up a few times. Fun...

Nothing in the "immediate" future. :ninja: I do have an eye open for an alternative cheap enclosure to take over the Jarhead model. Something the BareBones driver can drop into so the drivers can all have the same configuration. Want something to accommodate those that just want a home unit that...

Those are 5mm too long. The battery that fits well is 55 x 30 x 25mm. The 55mm length is maxed out for space inside. A little room to play (2-3mm) with the 30mm and 25mm measurements. :sherlock: I've done a fair bit of searching and they used to be on Amazon but no more. Can get similar on Ali...

The way the switch is set up isn't very forgiving for capless inserts. And looks like you went the full monty with the heat cycle. The VC gets pushed into the inside of the rubber tubing and when removed pulls and flanges the tubing out making it look like a splashdown. Might be able to trim off...

You'll find everyone has a bit different measurement here. Lots of variables in the equation. Cap model/vintage, herb dryness/strain, AC/battery power and of course personal taste preference. In design, my goal is getting as close as possible to the click without being too aggressive. Having the...

Just do a search on Amazon for "12.6 volt charger" Stick with the 1 amp units. ;)

Have you reinstalled the dowel? It needs a heat shield or the VC will melt the top of the tactile switch. If the dowel is lost, a small drop of JBQuick Weld, applied to the center of the tactile switch top will work just fine. :science: So you are just substituting the tach switch for the...

The above diagram is all correct. Not sure what you're asking. First off, the switch needs to be rated for at least 5 amp. The markings shown are: -,+ are the internal LED light. C - common or center pole of the switch. NO - Normally Open (used for this configuration) NC - Normally Closed (not...

Come on now, that one is just getting warmed up. I've seen them completely charred black and harder than rock. The darker the wooden heat shield gets, the harder it becomes. The same idea as our ancient ancestors did with their spear tips by putting in the fire. Show us again next year. :D

I believe you're asking about powering via a car's accessory jack..? Your car battery has enough power for sure. A Bare Bones or Jarhead will work fine. Only concern lyes with the accessory plugs nipple. Because of the high current, this contact point for the plug is very important and needs to...

Please contact via PM for individual failures and troubleshooting. :cool: Yes, center pin is positive. PSM has a charger and JH has a power supply. Not interchangeable. Also, cleaning does not make the switch easier to push. As for general mechanical switch maintenance, I've made an...

Howdy. Yes, the same chargers can be used for either unit. To measure the battery, it's best to measure while you have the VC inserted. This puts the battery under load and will measure lower on the readout. These gauges are the same as most gauges and just measures voltage. You get used to how...

Most likely it will be the tubing as would feel "soapy" if heated. It will need to come out by means of a hooked paperclip. Push beside the tubing and twist to have the hook snag from underneath. Pull it up a bit and repeat on the opposite side. Repeat until it comes out. Can likely just be...

You are correct that it's odd. There is no glue in there. The glass rhinestone is held down with thin double sided tape and is kept from any sideways movement by means of tubing that is pushed over the button shaft. I have never heard of one coming off while using normally. All the force is...

Hey guys, I received a very pleasant surprise today in the mail. @megatron, thank you very much for the customized enclosure. The fit is perfect and very easy to assemble. The modular just fits nice and tight and one only needs to align the tube slightly to center in the hole. The grommet fits...

Howdy. The BB driver stands about 55mm height. Comes ready to plug and play and gives time to ponder over an enclosure while giving it a workout. The power plug pigtail can also fit inside the choke coil for using stand alone without an enclosure. There is double sided foam tape on the bottom...