Search results

That's interesting, I'm not sure if it's the enail/coil that I'm using, or if my draw speed is too fast,..... Decided to put the temp back down to 600F and put the timer on it for 6min. I'll report back in a few...... Yea, like I thought, a really weak hit. I let it heat up to 600F for 6min...

Has anyone confirmed if the original hand blown wand works with the spherical heater cover? If it does, I assume the HFA can also be used? Still haven't obtained the pieces to make this SSV operational, so I'm still collecting ideas. Also, nobody responded to the question about who uses their...

Quick update, the elev8r has taken over daily driver responsibilities from the runt. Biggest negative of this vape is the heat up with coil. My cheap dabbing specialist controller will bring Temps up to 800F fairly quick, but I still let it set for a good ten minutes, to get a thorough heat...

Who in this thread uses their SSV, Sup, or DBV daily?

I'm a big fan of using a multi flame torch with my bricks. I turn the flame up also, so that the heat from the flame fills the intake completely Start with the larger, lighter blue flame outside of the flame intake, pointing into it. When drawing, find the spot in the intake that makes the...

Yea, but they didn't start their careers by cranking out home runs. It took many years of hard work and steroids to get to that consistent home run production. Once they got to that level, slow pitch, fast pitch, curveball, doesn't matter. The disk will make it easier to hit home runs...

The name "restrictor disk" can be misleading in my opinion. The disk simply delays combustion. Imagine a baseball pitcher trying to strike out a batter, and you're the batter. And imagine that if the ball gets past you, that's the same as combustion. Without the disk, you're trying to prevent...

I didn't see anything either. Maybe @DDave could chime in on the specifics of what people are talking about for their SSVs and DBV. :rockon:

Thanks homie, never hit an OG, but that is going to be my next brick down the line. :rockon:

Welcome friend! I can say that, I went from the dynavap to the sticky brick line because I wanted a bigger bowl than the dynavap. I got tired loading up 3-4 dynavaps before getting to where I wanted to be. When loading a full bowl in my Runt, I loosely fill the bowl all the way up to the brim...

The runt mouthpiece will fit the Jr, but it will not fit under the Jr's cap. So if you wanted to travel with the runt mouthpiece, a little carrying pouch or something is recommended. :rockon:

How do you remove them? My understanding from the video 7th floor has is that they blow a hole in the center after the ends are sealed, fill up with beads, then seal the hole? Maybe I'm missing something.

@Tweakz, I agree. You persuaded me to get an elev8r and I am thoroughly enjoying it. Comparing the two, I will say this: - Of the two, the elev8r is much heavier of a hitter, with half the material. Hands down, no doubt. - The SBrunt is still the champion when it comes to a combination of...

Would you please report back on if the glass beads end up fusing to the ceramic heater? That would be a deal breaker on the beads for me. :rockon:

Elev8 has a video out there that shows you can use a conical and spherical wand with the spherical glass heater cover. Not sure why you would pick the conical wand, unless you picked something that could also be used with the elev8r.

You can see the air intake is above the coil, maybe by 1/4in or more. The coil was loose, but I was able to kind of "wedge" the heater into the coil in a way that it won't move. I don't currently have a good stand for the setup. I was putting the heater/coil in a glass ashtray, but the thermal...

You were right. This thing is a hitter for sure. :evil: I fear that I may have just fucked up my tolerance. I hit the elev8r just now from the bowl I didn't finish last night. 775 temp, back to back to back to back hits. It's gotta another stir in her for sure, which is wild. Still using about...

I wound up getting an elev8r. Used it with a propane torch for about a week before I modded a 16mm coil to fit the heater. It's a sledge hammer of a vape. $99 for the elev8r kit from sneaky Pete, $74 for the enail and 16mm coil from the dabbing specialists. $173 for a setup that has annihilated...

You are correct my friend, I was deep into an elev8r session yesterday when making my post, so I meant to say heater cover and wand. I did not get a mouthpiece. :science: When funds become available, I'm thinking of picking up the heater stand upgrade, a mouthpiece (basic), a hands free...

So far, in my limited use, I have it setup that the heater will remain in the coil. I was keeping the heater/coil in a glass ashtray as a place to put the coil while it heated up, or in between stirring. Placing the hot coil in last night into a cold ashtray caused the ashtray to crack in half...