Search results

My Venty got a E04 recently that kept coming back even after resetting. It was replaced via RMA within 3 days. The new one that came now has Firmware 1.06. only differences i could discover: vibrates when going back go base temp from any booster temp. Display colors do not turn blue/purple when...

As I reported here some months ago S&B has already confirmed that they will incorporate a Haptic Feedback when the Venty goes back to the base temp with their next firmware. Unfortunately they will not consider NOT jumping back as long as you have drawn in the past 90sec. lokking forward to this...

Find any picture taken till now here: Gasket from oven to housing on ca. pic 44

My bricked venty and my replacement one do not have the ridges. Seems like they just optimized the use of material here, as the outside does not have an effect on the heating itself? This is just my guess… I just used a cutter knife, an scalpel would be even better (hope it doesn‘t break) to...

Here's my conclusion to an "swappable battery mod" for the venty: -It doesn't make too much sense, imho is taking a power bank with you way easier. -change batteries only in pairs of Samsung INR18650-30Q, remember left an right -only tried it physically with my bricked one, no real electrical...

I put everything in 99% iso and it does not destroy the o-rings. I usually take them out after 1-2min while all plastk parts maysoak in for 30 min….

My original now bricked venty did never throw any error and was always performing flawlessly. I never experienced any difference to my replacement one.....

Thanks for sharing these details! It just started with my venty falling on the ground and breaking a corner, swapping the broken part of the case was my original intention. All other things just came 1by1 as disassembling was easy. As I said a battery replacement mod is IMHO not too useful...

SolidAirr is right! one more idea for accessing the batteries easily: You could probably modify the back half of the casing(cut some of the rim that connects to the front half of the casing) so you could easily screw just the back half on and off to access the batteries. Or just leave the back...

Here are the next pics. If you need another angle or you need me to further disassemble just tell me. Battery-Swap-Mod can be achieved easily: 1. cut an opening in the back panel to access the batteries. 2. Un-Solder the batteries and maybe bend one half of the connectors down a little bit for a...

2s1p could be 2serial 1parallel ? What catches my attention was that one cathode and one anode are connected to each other and then to the board, whereas the other cathode and anode are connected individually to the board. the board and the oven are connected only via ribbon cable. They seem to...

Here are some Pics of my bricked and disassembled Venty. Will continue to detach the battery pack and disassemble the heating unit. Battery pack connected to board via 3 solid screws, you can see the screws or rather their terminals on the board top left, top right and bottom right. In general...

Thanks for checking the whole thread, so maybe i was dreaming about the faulty oven…. Still i am sure it is not the batteries so i will maybe try swapping them if it is „easy enough“ for me. If i do so i will report here. Till now i was only swapoing the bottom front case, only Electronics or...

Will post some pictures throughout this week, but the batteries are connected via soldering to a special frame, so not easy to just swap by „regular“ 18650s. But the pack of 2 or rather the mentioned frame can be screwed off and replaced pretty easily, not done it yet, just by inspection i...

Get one, it is great!

Dropped my Venty recently, from ca. 1,5m, the bottom corner of the housing broke, but it still worked perfectly. As I had my bricked Venty still handy I managed to easily swap the bottom front casing! It was a very easy process and it cannot be anticipated by S&B that I swapped it b/c they do...

May i ask: when did you brick your venty? Right after receiving the instrucions? Just asking so i can find out if it was a first-in-first-out with regards to when one bricked the device…. Thanks!

Yesterday I squeezed another bit of information out of the support team at S&B: I wrote them that 90sec. at the Booster Temps is too short. They SHould make it permanently, or at least configurable and add a vibration-notice when it switches back to base temp. This was their answer: „Das...

ordered it via storz-bickel.com. It is „out of stock“ because of problems with some devices. Just read the last 2-3 pages on this thread. Will probably become available again as soon as they sorted the problems out….

I ordered my Venty on the day it launched, received it two days later. Not any issue until now. Very pleased by the airflow and the fact that it will produce consistent rsult no matter of the way you draw. Best vapo i used up to now. I received the invitation for the readout of my device, and i...